Console Switches and Indicators Test | Whirlpool GVW9959K-0 instruction

Console Switches and Indicators Test

The console switches and indicators can be tested by pressing the following touchpads:

SOAK - CYCLE SIGNAL - SOAK - CYCLE SIGNAL

within five (5) seconds while the machine is in Standby Mode. The 7-segment LED will display “dt”.

1. Press the START pad.

Pressing each touchpad will cause a beep to sound and control one or more LEDs as shown.

Options

Status

So ak	Wa sh	Rinse
	Wa sh		Extra
				Sp in &

			Rinse		Cycle
			Rinse	Fluff	Cycle
					Complete

Extra Heavy	Hot	Cold
Heavy	Warm	Warm	Assured
			Assured
Normal	Warm	Cold	Water
Light	Cold	Cold	Tem p	Louder	Estimated Time
Light	Cold	Cold		Louder	Remaining
Refresh	Cold	Cold		Softer	Remaining
				Softer
				Off
				Off

Start

Stop

Canc el

SOAK	CYCLE
	SIGNAL

Fig. 4-3

If none of the LEDs light up:

•Visually check that connectors P11 and P12 are inserted all the way into the machine controller. If these connectors are properly installed, remove P11 and P12 from the control board while the power is still on.

If a particular group of LEDs does not light up:

•A group or combination of LEDs share a common electronic connection. If this connection is open, all of the LEDs in the group will be disabled. Replace the console panel/touchpad assem- bly.

If a single LED does not light up:

•Press the touchpad associated with the LED several times. If the LED does not light up, the LED has failed. Replace the console panel/touchpad assembly.

If no beep sound is heard:

•If the associated LEDs do light up, it is possible that the beeper circuit has failed. Check touchpad functioning before replacing the control board.

If no washer function is activated when a particular touchpad is pressed:

•If the associated LEDs do light up, it is possible that the control board has failed. Check touchpad functioning before replacing the control board.

52

Image 56

Whirlpool GVW9959K-0 Console Switches and Indicators Test, If none of the LEDs light up, If a single LED does not light up

Contents

Page Introduction Table of Contents Model Number Designator Model Number G V W 9 9 5 9 K Q SafetyMODEL/SERIAL Number Plate Serial Number Designator Installation ConsiderationsSection ONE For a permanently connected washer Tools needed Parts Supplied DrainSystem ConnectingtheDrainHose InstallationChecklist Use&CareInformation Theory of Operation Section TWONutation Control Panel Soil Level Operational Cycle Default Wash and SpinOption Descriptions Water Temp Assured Water TempATC Thresholds Whitest Whites End of Cycle Signal Additional Options Drive Motor Machine ControllerMotor Controller Peekaboo Mode Leveler Universal Joint Shield Capacitor Interlock SwitchesDrive System OPR FLD Pressure SwitchesLOG Valve Assembly Recirculation and Drain Water Pump/Pump MotorOuter Tub Recirculation Drain Changing Cycles and OptionsChanging Cycles after pressing Start Changing Options after pressing Start Operational Cycle Notes Drive Motor Notes Pump Drive Description Water Description Water Pump Drive Duration Description Water Pump Drive Pump Drive Description Action Speed Pump Drive Description Delicate/Casual SPIN+RECIRC+FILL Wash Detergent PS Controlled Recirc Spin Handwash Garments are labelled Hand Wash because Extend Spin Cycle Soak CycleExtra Rinse When to use Rinse & Spin To use or change Rinse & Spin settingsSuds Lock Detection/Cleanout Rinse & Spin Component Access Special TOOLS/PARTS Required for ServiceSection Three Component Location Accessing Components in the Console Electrostatic Discharge ESD Sensitive Electronics Removing the Console Removing Console ComponentsRemoving the Machine Control Board Removing the Motor Control Board Removing the Pressure Switches Removing the Log Valve Assembly Accessing Components Beneath the Washer TOP Raising the Washer Top to the Service Position Removing Components in the Tub Ket. Fig Reassembling Tub Components 18b Tab Removing the Front Cabinet Panel Accessing Components Beneath the TUBComponents Accessible with Front Cabinet Panel Removed Servicing Components from the Bottom of the Washer Removing the Drive MotorRemoving the Thrust Plate Motor mounting bracket to the motor plate Removing the Brake Assembly/Nutate Shaft 32 shows all the components of the thrust plate assembly Replacing the Outer Tub Removing the Pump and Pump MotorReplacing the Capacitor Section Four Troubleshooting and DiagnosisTroubleshooting Chart Overfills Won’t NutateWon’t Spin Motor Overheats Temperature Won’t DrainWasher Vibrating Incorrect Water Power Failure Processor ResetError Load is Wrinkled Lid Switch Error Long DrainAverage Current Limit Self Diagnostic Routines Automatic Service Diagnostics ModeOpen Lid Suds Lock Running Nutate or Spin Manual Diagnostic ModePressSOAK Cycle Signal Soak Cycle Signal Pump Drain/Recirculation Nutate and Recirculate Test Water Inlet and Dispenser VALVE, Operating PS Test Console Switches and Indicators Test If none of the LEDs light upIf a particular group of LEDs does not light up If a single LED does not light up KEY Switch Matrix Checking Touchpad Functioning Sales Demo Mode Checking Drive and Pump Motor Continuity Water Inlet and Dispenser Solenoid Test Troubleshooting Tests120VAC Electrical Supply Motor Controller Motor and Motor Control System TestMachine Control Relay If the fill valves are working properly Automatic Temperature Control TestDrive Motor and Wiring Harness Operating and Over Fill Pressure Switch Test Drain/Recirculation TestPage Page Section Five Wiring DiagramTech Tips Component Resistance Chart Warranty Information United States Rprt