![Air Conditioner User Menus](/images/new-backgrounds/52208/522089x1.webp)
Advanced Installer Configuration Menu
Air Conditioner User Menus
Status
Parameter | Option |
|
| Comments |
|
|
|
|
|
Compressor | Off, On |
|
| Compressor Status |
|
|
| ||
Mode | AC, AC1, AC2, Time | System Mode of Operation | ||
| Delay, Off |
|
|
|
|
|
|
|
|
Comp Hi Pres SW | Closed, Open |
|
| AC High Pressure Switch Status |
|
|
|
|
|
Comp Lo Pres SW | Closed, Open |
|
| AC Low Pressure Switch Status |
|
|
|
|
|
Outdr Temp Sens | XXXF, FLT |
|
| Outdoor Ambient Temperature Display |
(if enabled) |
|
|
| (if installed and enabled in setup) |
|
|
|
| This option will not appear unless the sensor |
|
|
|
| is enabled |
|
|
|
|
|
|
|
|
|
|
2 Week History (2 WK HIST) |
|
|
| |
Parameter | Indications |
|
| Comments |
|
|
|
|
|
2wk Y1 Hrs | XXX | 2 Week First Stage Cooling Hours of Operation | ||
|
|
|
|
|
2wk Y1 Cycles | XXXX | 2 Week First Stage Cooling Cycles | ||
|
|
|
|
|
2wk Y2 Hrs | XXX | 2 Week Second Stage Cooling Hours Operation | ||
|
|
|
|
|
2wk Y2 Cycles | XXXX | 2 Week Second Stage Cooling Cycles | ||
|
|
|
|
|
|
|
|
|
|
Life History (LIFE HIST) |
|
|
| |
Parameter | Indications |
|
| Comments |
|
|
|
|
|
Total Days Pwrd | XXXX |
| Total number of days control has been | |
|
|
| powered | |
|
|
|
|
|
Y1 Hrs | XXXXXX |
| First Stage Cooling Hours of Operation | |
|
|
|
|
|
Y1 Cycles | XXXXXX |
| First Stage Cooling Cycles | |
|
|
|
|
|
Y2 Hrs | XXXXXX |
| Second Stage Cooling Hours of Operation | |
|
|
|
|
|
Y2 Cycles | XXXXXX |
| Second Stage Cooling Cycles | |
|
|
|
|
|
Installation
Quick Install Steps
•Determine location of thermostat installation.
•Mount thermostat base to wall.
•Connect wires to thermostat base.
•Remove battery tag to provide battery power to the thermostat.
•Attach thermostat to base.
•Turn on power to system. Allow approximately 1 minute for the system to configure.
•Set the time
•Select thermostat operating options in the Thermostat Options Configuration Menu.
•Perform thermostat/system operation checkout.
•Program thermostat or accept factory programming.
•Touch Run Schedule.
Installing thermostat
•Pull the thermostat body off the thermostat base. Forcing or prying thermostat will cause damage to the unit.
•Place base at installation location and mark mounting hole locations on wall using base as a template.
•Move base out of the way. Drill mounting holes.
•Attach base snugly to wall using two mounting screws. Levelling is for appearance only and will not affect thermostat operation.
•Connect wires to terminal block on base.
•Push excess wire into wall and plug hole with a fire resistant material (such as fiberglass insulation) to prevent drafts from affecting thermostat operation.
•Remove battery tag to provide battery power to thermostat.
•Carefully line the thermostat up with the base and snap into place.