Wolf Appliance Company DF484CG manual T T I N G C O N T R O L S T T I N G C O N T Ro L S

W O L F D U A L F U E L R A N G E OVEN OPERATION

TEMPERATURE PROBE F E AT U R E
S E T T I N G C O N T R O L S		S E T T I N G C O N T RO L S
For Temperature Probe feature with meats:		For Temperature Probe feature with breads:
1)	Preheat oven to desired oven temperature	1)	Preheat oven to desired oven temperature
	in desired mode.		in Bake or Bake Stone modes.
2)	Place meat on a rack in the roasting pan.	2)	Place bread on bake stone or in oven in
	Insert the probe sensor into the thickest		bread pans.
	part of the meat as described in Tips For	3)	Bake 10 minutes at desired oven
	Success on page 37.
			temperature.
3)	When the oven signals that preheat is	4)	Insert probe sensor into the thickest part
	completed, use a dry pot holder to lift the
			of the bread.
	probe sensor cover. Slide the probe connec-
		5)
	tor into the receptacle on the wall of the		Using a dry pot holder, lift the probe sensor
	oven until it snaps into place. Close the		cover. Slide the probe connector into the
	oven door.		receptacle on the wall of the oven until it
4) PROBE will be illuminated on the hidden			snaps into place. Close the oven door.
		6) PROBE will be illuminated on the hidden
	control panel. The probe temperature is
	preset at 160˚F (70˚C).		control panel. The probe temperature is
	To change the desired final probe tempera-		preset at 160˚F (70˚C).
	ture setting from 160˚F (70˚C), immediately		To change the desired final probe tempera-
	hold the oven selector knob to the right to		ture setting from 160˚F (70˚C), immediately
	increase the probe temperature or to the		turn the oven selector knob to the right to
	left to decrease the probe temperature.		increase the probe temperature or to the
5) Touch ENTER on the hidden control panel			left to decrease the probe temperature.
			Breads are baked to an internal temperature
	or after two seconds the oven will turn on
			of 195˚F (90˚C) to 210˚F (100˚C).
	by default.
		7) Touch ENTER on the hidden control panel
	Once the probe set point has been
			or after two seconds the oven will turn on
	programmed, the oven knob display will
			by default.
	alternate between the probe set point and
	the word “Lo” until the internal tempera-		Once the probe set point has been
	ture reaches 70˚F (20˚C). Then the display		programmed, the oven knob display will
	alternates between the probe set point and		alternate between the probe set point and
	the actual probe temperature.		the word “Lo” until the internal tempera-
6)	When the desired internal temperature has		ture reaches 70˚F (20˚C). Then the display
			alternates between the probe set point and
	been reached, the oven will chime. Recheck
			the actual probe temperature.
	the internal temperature by removing and
		8)
	then reinserting the probe into the meat.		When the desired internal temperature has
7)	Remove probe and food.		been reached, the oven will chime. Remove
			probe and food.
8) Turn oven selector knob bezel to OFF to		9) Turn oven selector knob bezel to OFF to
	end this feature.
			end this feature.
IMPORTANT NOTE: If the probe connector is
not fully seated into the probe receptacle,
PROBE will flash in the display. Refer to the
		Probe and probe sensor cover become
Troubleshooting Guide on page 53.
		very hot. Handle with a dry pot holder.
Dimensions in parentheses are in
millimeters unless otherwise specified.			39