Gearbox Oil Level, Connecting to Power | Woodstock W1754S specs

W1754 20" Planer With Mobile Base

SET UP

4.Mount the foot pedal onto the caster and insert the pin between the two parts.

5.Lock the caster and pedal in place with the E-clip and washers, as shown in Figure 9.�

Gearbox Oil Level

Before starting your machine for the first time, make sure the gearbox has oil. The proper oil level is just even with the bottom of the fill plug hole. The gearbox uses 80W-90W automotive grade gear oil.

To check the gearbox oil level, do these steps:

1.Wipe the outside of the fill plug clean.

2.Using a 6mm hex wrench, remove the gearbox fill plug (Figure 10).

3.Using the short end of the hex wrench (make sure it is CLEAN), dip it inside the fill hole and remove it. (Do not drop the wrench into the gearbox!)

—If the end of the hex wrench is coated with oil, then the gearbox oil level is okay. Replace the fill plug and continue with set up.

—If the end of the hex wrench is not coated with oil, then fill the gearbox with 80-90W gear oil until the oil reaches the top of the fill plug.

Note: Replace the gearbox oil after the first 20 hours of operation. This is a normal break-in pro- cedure. See Lubrication on Page 25.

Connecting to Power

Make sure you have read and followed precautions listed on Page 8, before connecting your planer to power. The POWER button and STOP button (Figure 11) should illumi- nate when the planer is connected to the power. Refer to Page 40 to troubleshoot any problems.

Foot Pedal	Pin
Foot Pedal
	Hex Bolt
Caster	Bracket
Caster

Figure 9. Foot pedal and caster

assembled.

Figure 10. Gearbox fill plug location.

Figure 11. W1754 control panel.

-14-

Image 28

Woodstock W1754S owner manual Gearbox Oil Level, Connecting to Power, To check the gearbox oil level, do these steps

Contents

Model W1754S Planer With Spiral Cutterhead B68=C HE886IDCH `gg`e`d\ej`fej Xikfe Headstock Breakdown Headstock Parts List Description Gearbox Breakdown Cabinet Breakdown Gearbox Parts List Table Breakdown Columns Breakdown Labels & Cosmetics Page Planer with Mobile Base Page Contents Introduction Woodstock Technical Support Introduction Controls and Features Safety Standard Safety Instructions Always Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers Electrical Electrical Specifications220V Operation Setup Items Needed for SetupUnpacking Inventory Lifting Planer Machine PlacementHardware and Tools Not Shown Cleaning Machine These items are coated and must be cleaned Extension Wings Extension wing fasteners Leveling controls To install the caster and foot pedal, do these steps To install the handwheel, do these stepsHandwheel, Dust Hood Caster Gearbox Oil Level Connecting to PowerTo check the gearbox oil level, do these steps Test Run To perform a test run, do these steps Recommended Adjustments Tighten V-Belts Operations GeneralBasic Operation Basic steps of operating the planer are as follows Operation Tips Feed Speed Feed control knob positions To adjust the bed rollers, do these steps Adjustment Height Range 002-0.020Bed Rollers Accessories Planer Accessories Operations Cleaning MaintenanceMaintenance Schedule Belts To adjust/replace the V-belts, do these stepsPulley Alignment on Lubrication Inspecting Knives ServiceTo inspect the knives, do these steps Setting/Replacing Knives To set the knives, do these steps To adjust the chain tension, do these steps Chain Tension Table Parallelism Maximum Allowable Tolerances To adjust the table parallelism, do these steps Table micro-adjustment screws Rollers, Breaker Pressure Bar Heights Distance Below Knife Edge at *BDC Location Service To adjust roller spring tension, do these steps Spring Tension Loosen the chip deflector mounting bolts see Figure Scale CalibrationTo calibrate the scale, do these steps Anti-Kickback Fingers Anti-kickback fingers Pulley Alignment Example of checking belt Alignment W1754 Electrical Components Motor junction box W1754 20 Planer With Mobile Base Troubleshooting Problem Possible Cause Corrective Action Cutting Headstock Assembly Parts Breakdown Headstock Assembly Parts List PART# Description Cutterheadpulley Gearbox Parts Breakdown XPSB06M CAPSCREWM6-1X25 Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Warranty Registration Comments BOX BELLINGHAM, WA