Manuals / Woodstock / Power Tools / Planer

Woodstock W1754S owner manual Labels & Cosmetics

Models: W1754S

1 72

Download 72 pages 26.81 Kb

Page 11

W1754S 20" Planer with Spiral Cutterhead

Labels & Cosmetics

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Woodstock International, Inc. at (360) 734-3482 or www.shopfoxtools.com to order new labels.

-()			-(* -(,	-(-	-(+
-()		-'(	-')		-(*
	-''	-'(	-')
	-''
			-(.
			-'*

-('

-'0 -'/

-'.

-'-	-(-

-',

-'+

REF	PART #	DESCRIPTION
600	XLABEL-12	READ MANUAL LABEL
601	X1754S601	MACHINE ID LABEL
602	XLABEL-11	SAFETY GLASSES LABEL
603	X1754603	SPEED CHANGE LABEL
604	X1754604	DECORATIVE STRIPE TAPE
605	X1754S605	MODEL NUMBER LABEL
606	X1754606	SHOP FOX LOGO PLATE
607	XPPAINT-2	SHOP FOX WHITE
608	XLABEL-1	EAR PROTECTION LABEL

REF	PART #	DESCRIPTION
609	X1754609	RESPIRATOR LABEL
610	XLABEL-04	ELECTRICITY LABEL
612	XPPAINT-7	SHOP FOX BLACK
613	X1754613	LUBRICATION LABEL
614	X1754614	CUTTERHEAD WARNING LABEL
615	X1754615	DISCONNECT POWER LABEL
616	X1754616	SHUT COVER WARNING LABEL
617	X1754617	HAND WHEEL LABEL

-11-

Image 11

Woodstock W1754S owner manual Labels & Cosmetics

Contents

Model W1754S Planer With Spiral Cutterhead B68=C HE886IDCH `gg`e`d\ej`fej Xikfe Headstock Breakdown Description Headstock Parts ListGearbox Breakdown Cabinet Breakdown Gearbox Parts List Table Breakdown Columns Breakdown Labels & Cosmetics Page Planer with Mobile Base Page Contents Woodstock Technical Support IntroductionIntroduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers 220V Operation Electrical SpecificationsElectrical Inventory SetupItems Needed for Setup UnpackingHardware and Tools Not Shown Machine PlacementLifting Planer These items are coated and must be cleaned Cleaning MachineExtension wing fasteners Leveling controls Extension WingsHandwheel, Dust Hood Caster To install the handwheel, do these stepsTo install the caster and foot pedal, do these steps To check the gearbox oil level, do these steps Connecting to PowerGearbox Oil Level To perform a test run, do these steps Test RunTighten V-Belts Recommended AdjustmentsBasic steps of operating the planer are as follows OperationsGeneral Basic OperationOperation Tips Feed control knob positions Feed SpeedBed Rollers Adjustment Height Range 002-0.020To adjust the bed rollers, do these steps Planer Accessories AccessoriesOperations Maintenance Schedule MaintenanceCleaning Pulley Alignment on To adjust/replace the V-belts, do these stepsBelts Lubrication To inspect the knives, do these steps ServiceInspecting Knives To set the knives, do these steps Setting/Replacing KnivesChain Tension To adjust the chain tension, do these stepsMaximum Allowable Tolerances Table ParallelismTable micro-adjustment screws To adjust the table parallelism, do these stepsDistance Below Knife Edge at *BDC Rollers, Breaker Pressure Bar HeightsLocation Service Spring Tension To adjust roller spring tension, do these stepsTo calibrate the scale, do these steps Scale CalibrationLoosen the chip deflector mounting bolts see Figure Anti-kickback fingers Anti-Kickback FingersExample of checking belt Alignment Pulley AlignmentMotor junction box W1754 Electrical ComponentsW1754 20 Planer With Mobile Base Problem Possible Cause Corrective Action TroubleshootingCutting Headstock Assembly Parts Breakdown PART# Description Headstock Assembly Parts ListCutterheadpulley Gearbox Parts Breakdown XPSB06M CAPSCREWM6-1X25 Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Comments Warranty RegistrationBOX BELLINGHAM, WA