Labels & Cosmetic Parts | Woodstock W1754S instruction

W1754 20" Planer With Mobile Base

Labels & Cosmetic Parts

Safety labels warn about machine hazards and how to prevent machine damage or injury. The owner of this machine MUST maintain the original location and readability of all labels on this machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www. shopfoxtools.com to order new labels.

				613	614	616	615	613
	612			613	614
			601
611				602
611		600		602
		600
				617

603

610

609

608

607

606

605

604

REF	PART�#	DESCRIPTION
600	XLABEL-12	READ�MANUAL�LABEL
601	X1754601	MACHINE�ID�LABEL
602	XLABEL-11	SAFETY�GLASSES�LABEL
603	X1754603	SPEED�CHANGE�LABEL
604	X1754604	DECORATIVE�STRIPE�TAPE
605	X1754605	MODEL�NUMBER�LABEL
606	X1754606	SHOP�FOX�LOGO�PLATE
607	X1754607	SHOP�FOX�WHITE
608	XLABEL-1	EAR�PROTECTION�LABEL

REF	PART�#	DESCRIPTION
609	X1754609	RESPIRATOR�LABEL
610	XLABEL-04	ELECTRICITY�LABEL
611	X1754611	CONTROL�PANEL�LABEL
612	XPPAINT-7	SHOP�FOX�BLACK
613	X1754613	LUBRICATION�LABEL
614	X1754614	CUTTERHEAD�WARNING�LABEL
615	X1754615	DISCONNECT�POWER�LABEL
616	X1754616	SHUT�COVER�WARNING�LABEL
617	X1754617	HAND�WHEEL�LABEL

PARTS

-52-

Image 66

Woodstock W1754S owner manual Labels & Cosmetic Parts

Contents

Model W1754S Planer With Spiral Cutterhead B68=C HE886IDCH `gg`e`d\ej`fej Xikfe Headstock Breakdown Headstock Parts List Description Gearbox Breakdown Cabinet Breakdown Gearbox Parts List Table Breakdown Columns Breakdown Labels & Cosmetics Page Planer with Mobile Base Page Contents Introduction Woodstock Technical Support Introduction Controls and Features Safety Standard Safety Instructions Always Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers Electrical Specifications Electrical220V Operation Unpacking SetupItems Needed for Setup Inventory Machine Placement Lifting PlanerHardware and Tools Not Shown Cleaning Machine These items are coated and must be cleaned Extension Wings Extension wing fasteners Leveling controls To install the handwheel, do these steps To install the caster and foot pedal, do these stepsHandwheel, Dust Hood Caster Connecting to Power Gearbox Oil LevelTo check the gearbox oil level, do these steps Test Run To perform a test run, do these steps Recommended Adjustments Tighten V-Belts Basic Operation OperationsGeneral Basic steps of operating the planer are as follows Operation Tips Feed Speed Feed control knob positions Adjustment Height Range 002-0.020 To adjust the bed rollers, do these stepsBed Rollers Accessories Planer Accessories Operations Maintenance CleaningMaintenance Schedule To adjust/replace the V-belts, do these steps BeltsPulley Alignment on Lubrication Service Inspecting KnivesTo inspect the knives, do these steps Setting/Replacing Knives To set the knives, do these steps To adjust the chain tension, do these steps Chain Tension Table Parallelism Maximum Allowable Tolerances To adjust the table parallelism, do these steps Table micro-adjustment screws Rollers, Breaker Pressure Bar Heights Distance Below Knife Edge at *BDC Location Service To adjust roller spring tension, do these steps Spring Tension Scale Calibration Loosen the chip deflector mounting bolts see FigureTo calibrate the scale, do these steps Anti-Kickback Fingers Anti-kickback fingers Pulley Alignment Example of checking belt Alignment W1754 Electrical Components Motor junction box W1754 20 Planer With Mobile Base Troubleshooting Problem Possible Cause Corrective Action Cutting Headstock Assembly Parts Breakdown Headstock Assembly Parts List PART# Description Cutterheadpulley Gearbox Parts Breakdown XPSB06M CAPSCREWM6-1X25 Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Warranty Registration Comments BOX BELLINGHAM, WA