Belts, Pulley Alignment on | Woodstock W1754S specs

W1754 20" Planer With Mobile Base

MAINTENANCE

V-Belts

V-belt removal and replacement is simply a matter of adjusting the motor mount, rolling the belts off of the pulleys and replacing them with new belts, then reten- sioning them.

Always replace V-belts with a matched set of 3 belts, or belt tension may be unven among the 3 belts and may cause premature belt failure.

To adjust/replace the V-belts, do these steps:

1.DISCONNECT THE PLANER FROM POWER!

2.Remove the motor and front access panels and V- belt cover.

3.Using a 19mm wrench, loosen the hex nuts on the tension rods shown in Figure 15.

4.Lift the motor up and slide the V-belts off of the pulleys.

5.Make sure the pulleys are in alignment as outlined in

Pulley Alignment on Page 37.

6.Slide the new belts onto the pulley, lower the motor, and tighten the fasteners loosened in Step 3.

7.Check belt deflection as shown in Figure .

Note: The correct tension for the V-belts is 1⁄4"–1⁄2" deflection when pushed in the center with moderate pressure. After the first 16 hours of belt life, reten- sion them, as they will stretch and seat during this time.

8. Close the V-belt cover and replace the front and motor access panels.

OFF

Tension

Rod

Figure 15. Fasteners needed to be loosened for V-belt replacement.

��

��

��

Figure 16. Checking belt deflection.

-24-

Image 38

Woodstock W1754S owner manual Belts, To adjust/replace the V-belts, do these steps, Pulley Alignment on

Contents

Model W1754S Planer With Spiral Cutterhead B68=C HE886IDCH `gg`e`d\ej`fej Xikfe Headstock Breakdown Headstock Parts List Description Gearbox Breakdown Cabinet Breakdown Gearbox Parts List Table Breakdown Columns Breakdown Labels & Cosmetics Page Planer with Mobile Base Page Contents Introduction Woodstock Technical Support Introduction Controls and Features Safety Standard Safety Instructions Always Lock Mobile Bases Before Operating Machinery Additional Safety Instructions for Planers 220V Operation Electrical SpecificationsElectrical Unpacking SetupItems Needed for Setup Inventory Hardware and Tools Not Shown Machine PlacementLifting Planer Cleaning Machine These items are coated and must be cleaned Extension Wings Extension wing fasteners Leveling controls Handwheel, Dust Hood Caster To install the handwheel, do these stepsTo install the caster and foot pedal, do these steps To check the gearbox oil level, do these steps Connecting to PowerGearbox Oil Level Test Run To perform a test run, do these steps Recommended Adjustments Tighten V-Belts Basic Operation OperationsGeneral Basic steps of operating the planer are as follows Operation Tips Feed Speed Feed control knob positions Bed Rollers Adjustment Height Range 002-0.020To adjust the bed rollers, do these steps Accessories Planer Accessories Operations Maintenance Schedule MaintenanceCleaning Pulley Alignment on To adjust/replace the V-belts, do these stepsBelts Lubrication To inspect the knives, do these steps ServiceInspecting Knives Setting/Replacing Knives To set the knives, do these steps To adjust the chain tension, do these steps Chain Tension Table Parallelism Maximum Allowable Tolerances To adjust the table parallelism, do these steps Table micro-adjustment screws Rollers, Breaker Pressure Bar Heights Distance Below Knife Edge at *BDC Location Service To adjust roller spring tension, do these steps Spring Tension To calibrate the scale, do these steps Scale CalibrationLoosen the chip deflector mounting bolts see Figure Anti-Kickback Fingers Anti-kickback fingers Pulley Alignment Example of checking belt Alignment W1754 Electrical Components Motor junction box W1754 20 Planer With Mobile Base Troubleshooting Problem Possible Cause Corrective Action Cutting Headstock Assembly Parts Breakdown Headstock Assembly Parts List PART# Description Cutterheadpulley Gearbox Parts Breakdown XPSB06M CAPSCREWM6-1X25 Base Breakdown Base Parts List Table Breakdown & List Columns Breakdown Columns Parts List Labels & Cosmetic Parts Warranty Page Warranty Registration Comments BOX BELLINGHAM, WA