Manuals / Xantrex Technology / Lawn and Garden / Portable Generator

Xantrex Technology Link 1000 Advanced Function Values, F02 Display Sleep Default On Range On, Off

Models: Link 1000

1 74

Download 74 pages 11.15 Kb

Page 37

Advanced Function Values

About Link 1000 Settings

Advanced Function Values

The Link 1000 has sixteen advanced functions. The default setting is appropriate for most, and you should not change a value unless you understand the consequence of the change.

Note: If you are monitoring more than one battery:

•Change Function F11, Second Battery Voltage Sense.

•Record the software revision number on page 60. (See “F15 Display Software Revision Number” on page 34.)

How to Enter Setup Mode and Change a Value: Reminder

The procedure for entering Setup mode and changing a value is given on page 20.

F01 Auto Display Scanning

Default: Off

Range: Off, On

When Auto Display Scanning is On, the display automatically scrolls through Volts, Amps, Ah, and Time remaining. Each value is displayed for four seconds.

If Second Battery Voltage Sense (F11) is also on, two voltages are shown. The flashing Volts status LED indicates that the voltage displayed is that of the second battery bank.

F02 Display Sleep

Default: On

Range: On, Off

This function turns off the Numeric Display and the Display Units LEDs. All the other LEDs—BATTERY STATUS light bar, AC IN, Charger status LEDs, CHARGE LED, and INVERT LED—stay on.

29

Image 37

Xantrex Technology Link 1000 manual Advanced Function Values, How to Enter Setup Mode and Change a Value Reminder

Contents

Owner’s Guide LinkTrademark About XantrexNotice of Copyright Disclaimer2 Installing the Link Contents1 Introducing Link 3 Setting up the Link 4 Using the Link B Product and System Information A SpecificationsIndex ContentsBATTERY STATUS Light Bar Link 1000 Control Panel System Overview WiringFigures Display Panel and Mounting Plate Link 1000 Mounting PlatePage Introducing Link The features on its control panelChapter 1 describes The Link 1000’s control and monitoring functionsInverter/Charger Control Functions Introducing the LinkMonitoring Functions Battery history including Present charge efficiency The time remaining in your battery before it is completely dischargedThe number of deep cycles the battery has had The deepest level of discharge The average level of dischargeFigure 1 Link 1000 Control Panel Reading the Link 1000 Control Panel2, 3 Numeric display and display units Indicates that AC power is present Where to go From HereTo install the Link 1000, see page To set up the Link 1000, see page To use the Link 1000, see pageAn overview of the installation process Installing the LinkA list of installation tools and equipment Installation procedures Chapter 2 givesRefer to Figure 2 on page Planning the InstallationInstallation Considerations The shunt sense leads must be 18AWG twisted pair wires Overview of Installation Steps Installing the LinkInstalling the Link Figure 2 System Overview WiringBattery BatteryTo mount the control panel Mounting the Link 1000 Control PanelTo mount and cable the shunt Mounting and Cabling the ShuntTo wire the terminal block Wiring the Terminal BlockTo connect the terminal block wires Connecting Terminal Block Wires to Shunt and BatteryConnecting the Phone Cable Installing FusesTesting the Installation To install fusesDisconnecting the Inverter/Charger MaintenanceHow to set up the Link 1000 to best suit your battery system Setting up the LinkEach setting as well as the options for each setting Whether you should change settings or leave the default settingTo enter Setup mode and change a value About Link 1000 SettingsResetting Values Locking Your Setup ValuesTo lock the setup To reset valuesBattery Capacity To change the Battery Type setting To change the Battery Capacity settingChanging the Ambient Temperature Setting To change the Ambient Temperature settingCharged Parameters To change the Charged Voltage settingTo change the Charged Current Percentage To change the Time Remaining settingChanging the Time Remaining Setting Changing the Power Share Setting To change Power Share valuesChanging the Idle Mode Setting To change the Idle mode settingHow to Enter Setup Mode and Change a Value Reminder Advanced Function ValuesF01 Auto Display Scanning Default Off Range Off, On F02 Display Sleep Default On Range On, OffRange 30 F-120 F -1.11 C-48.8 C in 10 increments Range Off and On. On = use alternative energy defaults Default 1.25 for liquid lead-acid batteries. Battery Type set to Type Default 0 Liquid Cell F14 mode The RESET and DATA LEDs are orange-yellow Chapter 4 tells you how to Read the battery’s state-of-charge Using the LinkTurn on the invert function Change the Idle mode setting Charge and equalize the batteries Determine battery capacityChoosing a Display Unit Volts, Amps, Ah, or Time Monitoring FunctionsTo change the display unit BATTERY STATUS Reading the Battery State-of-ChargeInverter Functions Changing the Idle Mode SettingTurning on the Invert Function To turn on the invert functionSummary of CHARGER STATUS LEDs Charging FunctionsEqualizing the Batteries Charging the BatteriesTo start a charge cycle WARNING Explosion HazardTo end an equalization cycle manually To start an equalization cycleBattery Capacity Testing Activating Power ShareTo change the Power Share setting See pageTo test battery capacity To synchronize the Link 1000 to the battery Synchronizing the Link 1000 to the BatteryOver-charge Ah Accumulation of Positive Ah To access battery history Battery HistoryParameters have been met since the last time it was reset to the factory defaults. A discharge of less than 10% of battery capacity is not counted as a “cycle” Error Reading Error CodesCode MeaningCode ErrorMeaning AC backfeedCode ErrorMeaning E012Electrical and physical specifications for the Link Default settings SpecificationsSpecifications are subject to change without notice Appendix A listsControl Panel Physical Specifications Control Panel Electrical SpecificationsControl Panel Electrical Specifications Inverter/Charger Controls Default SettingsMonitoring Functions Page Product and System Information The warranty for your LinkAppendix B contains Instructions for returning the product for servicingWarranty Proof of purchase may be in any one of the following forms Product DisclaimerExclusions Return Material Procedure Return Material Authorization PolicyWarning Limitations On Use Record these details in “Record of System Settings” on pageProduct Information Setting Record of System SettingsSetting Index SymbolsNumerics Page