Manuals / Xantrex Technology / Lawn and Garden / Portable Generator

Xantrex Technology Link 1000 manual Control Panel Electrical Specifications

Models: Link 1000

1 74

Download 74 pages 11.15 Kb

Page 60

Control Panel: Electrical Specifications

Control Panel: Electrical Specifications

Control Panel: Electrical Specifications

DC Power supply voltage	8–40 VDC. (Not for use with 32 volt
	systems.)

Power consumption	For 12 volt systems:
	• 90 mA (typical)
	• 170 mA (full display brightness)
	• 25 mA (sleep mode; only
	BATTERY STATUS LEDS on.)
	Values are approximately half on 24
	volt systems.

Voltage measurement range	0.1–50 VDC

Voltage resolution	0.05 VDC

Voltage accuracy	±0.10 VDC at full scale

Current measurement range	±500 Amps DC

Current resolution	• 0.1 amp DC (from ±0–±42.0
	amps)
	• 1 amp DC (from ±42–±500
	amps)

Current accuracy	• ±0.1 amp DC at full scale low
	range
	• ±1 amp DC at full scale high
	range

Current shunt	±0.25% ratio: 50mV @ 500A

Amp hour range	±1,999Ah

Time remaining range	255 hours maximum

Control Panel: Physical Specifications

Width	4.725 in. (120 mm)

Height	2.975 in. (75.5 mm)

Depth	1.075 in. (27.3 mm)

Weight	4.6 oz. (2 g)

Front panel finish	Water resistant, splash proof

52

Image 60

Xantrex Technology Link 1000 manual Control Panel Electrical Specifications, Control Panel Physical Specifications

Contents

Link Owner’s GuideAbout Xantrex TrademarkNotice of Copyright DisclaimerContents 2 Installing the Link1 Introducing Link 3 Setting up the Link 4 Using the Link A Specifications B Product and System InformationIndex ContentsLink 1000 Control Panel System Overview Wiring BATTERY STATUS Light BarFigures Display Panel and Mounting Plate Link 1000 Mounting PlatePage The features on its control panel Introducing LinkChapter 1 describes The Link 1000’s control and monitoring functionsIntroducing the Link Inverter/Charger Control FunctionsMonitoring Functions The time remaining in your battery before it is completely discharged Battery history including Present charge efficiencyThe number of deep cycles the battery has had The deepest level of discharge The average level of dischargeReading the Link 1000 Control Panel Figure 1 Link 1000 Control Panel2, 3 Numeric display and display units Where to go From Here Indicates that AC power is presentTo install the Link 1000, see page To set up the Link 1000, see page To use the Link 1000, see pageInstalling the Link An overview of the installation processA list of installation tools and equipment Installation procedures Chapter 2 givesPlanning the Installation Refer to Figure 2 on pageInstallation Considerations The shunt sense leads must be 18AWG twisted pair wires Installing the Link Overview of Installation StepsFigure 2 System Overview Wiring Installing the LinkBattery BatteryMounting the Link 1000 Control Panel To mount the control panelMounting and Cabling the Shunt To mount and cable the shuntWiring the Terminal Block To wire the terminal blockConnecting Terminal Block Wires to Shunt and Battery To connect the terminal block wiresInstalling Fuses Connecting the Phone CableTesting the Installation To install fusesMaintenance Disconnecting the Inverter/ChargerSetting up the Link How to set up the Link 1000 to best suit your battery systemEach setting as well as the options for each setting Whether you should change settings or leave the default settingAbout Link 1000 Settings To enter Setup mode and change a valueLocking Your Setup Values Resetting ValuesTo lock the setup To reset valuesBattery Capacity To change the Battery Capacity setting To change the Battery Type settingTo change the Ambient Temperature setting Changing the Ambient Temperature SettingTo change the Charged Voltage setting Charged ParametersTo change the Time Remaining setting To change the Charged Current PercentageChanging the Time Remaining Setting To change Power Share values Changing the Power Share SettingTo change the Idle mode setting Changing the Idle Mode SettingAdvanced Function Values How to Enter Setup Mode and Change a Value ReminderF01 Auto Display Scanning Default Off Range Off, On F02 Display Sleep Default On Range On, OffRange 30 F-120 F -1.11 C-48.8 C in 10 increments Range Off and On. On = use alternative energy defaults Default 1.25 for liquid lead-acid batteries. Battery Type set to Type Default 0 Liquid Cell F14 mode The RESET and DATA LEDs are orange-yellow Using the Link Chapter 4 tells you how to Read the battery’s state-of-chargeTurn on the invert function Change the Idle mode setting Charge and equalize the batteries Determine battery capacityMonitoring Functions Choosing a Display Unit Volts, Amps, Ah, or TimeTo change the display unit Reading the Battery State-of-Charge BATTERY STATUSChanging the Idle Mode Setting Inverter FunctionsTurning on the Invert Function To turn on the invert functionCharging Functions Summary of CHARGER STATUS LEDsCharging the Batteries Equalizing the BatteriesTo start a charge cycle WARNING Explosion HazardTo start an equalization cycle To end an equalization cycle manuallyActivating Power Share Battery Capacity TestingTo change the Power Share setting See pageTo test battery capacity Synchronizing the Link 1000 to the Battery To synchronize the Link 1000 to the batteryOver-charge Ah Accumulation of Positive Ah Battery History To access battery historyParameters have been met since the last time it was reset to the factory defaults. A discharge of less than 10% of battery capacity is not counted as a “cycle” Reading Error Codes ErrorCode MeaningError CodeMeaning AC backfeedError CodeMeaning E012Specifications Electrical and physical specifications for the Link Default settingsSpecifications are subject to change without notice Appendix A listsControl Panel Electrical Specifications Control Panel Physical SpecificationsControl Panel Electrical Specifications Default Settings Inverter/Charger ControlsMonitoring Functions Page The warranty for your Link Product and System InformationAppendix B contains Instructions for returning the product for servicingWarranty Proof of purchase may be in any one of the following forms Disclaimer ProductExclusions Return Material Authorization Policy Return Material ProcedureWarning Limitations On Use Record these details in “Record of System Settings” on pageProduct Information Record of System Settings SettingSetting Symbols IndexNumerics Page