Manuals / Xantrex Technology / Lawn and Garden / Portable Generator

Xantrex Technology Link 1000 manual Setting

Models: Link 1000

1 74

Download 74 pages 11.15 Kb

Page 70

Manual background

Record of System Settings

		Your
		Setting or
Setting		Recorded
Setting	Default	Data

Temperature Coefficient	0.5
(F07)

Peukert Exponent (F08)	1.25

Low Battery Discharge Floor	100%
(F09)

Battery Type (F10)	000 (liquid lead-
	acid)

Second Battery Voltage	Off
Sense (F11)

Active Temperature	Off
Compensation (F16)

62

Image 70

Xantrex Technology Link 1000 manual Setting

Contents

Link Owner’s GuideNotice of Copyright About XantrexTrademark Disclaimer2 Installing the Link Contents1 Introducing Link 3 Setting up the Link 4 Using the Link Index A SpecificationsB Product and System Information ContentsFigures Link 1000 Control Panel System Overview WiringBATTERY STATUS Light Bar Display Panel and Mounting Plate Link 1000 Mounting PlatePage Chapter 1 describes The features on its control panelIntroducing Link The Link 1000’s control and monitoring functionsInverter/Charger Control Functions Introducing the LinkMonitoring Functions The number of deep cycles the battery has had The time remaining in your battery before it is completely dischargedBattery history including Present charge efficiency The deepest level of discharge The average level of dischargeReading the Link 1000 Control Panel Figure 1 Link 1000 Control Panel2, 3 Numeric display and display units To install the Link 1000, see page To set up the Link 1000, see page Where to go From HereIndicates that AC power is present To use the Link 1000, see pageA list of installation tools and equipment Installation procedures Installing the LinkAn overview of the installation process Chapter 2 givesPlanning the Installation Refer to Figure 2 on pageInstallation Considerations The shunt sense leads must be 18AWG twisted pair wires Installing the Link Overview of Installation StepsBattery Figure 2 System Overview WiringInstalling the Link BatteryMounting the Link 1000 Control Panel To mount the control panelMounting and Cabling the Shunt To mount and cable the shuntWiring the Terminal Block To wire the terminal blockConnecting Terminal Block Wires to Shunt and Battery To connect the terminal block wiresTesting the Installation Installing FusesConnecting the Phone Cable To install fusesMaintenance Disconnecting the Inverter/ChargerEach setting as well as the options for each setting Setting up the LinkHow to set up the Link 1000 to best suit your battery system Whether you should change settings or leave the default settingAbout Link 1000 Settings To enter Setup mode and change a valueTo lock the setup Locking Your Setup ValuesResetting Values To reset valuesBattery Capacity To change the Battery Capacity setting To change the Battery Type settingTo change the Ambient Temperature setting Changing the Ambient Temperature SettingTo change the Charged Voltage setting Charged ParametersTo change the Charged Current Percentage To change the Time Remaining settingChanging the Time Remaining Setting To change Power Share values Changing the Power Share SettingTo change the Idle mode setting Changing the Idle Mode SettingF01 Auto Display Scanning Default Off Range Off, On Advanced Function ValuesHow to Enter Setup Mode and Change a Value Reminder F02 Display Sleep Default On Range On, OffRange 30 F-120 F -1.11 C-48.8 C in 10 increments Range Off and On. On = use alternative energy defaults Default 1.25 for liquid lead-acid batteries. Battery Type set to Type Default 0 Liquid Cell F14 mode The RESET and DATA LEDs are orange-yellow Turn on the invert function Change the Idle mode setting Using the LinkChapter 4 tells you how to Read the battery’s state-of-charge Charge and equalize the batteries Determine battery capacityChoosing a Display Unit Volts, Amps, Ah, or Time Monitoring FunctionsTo change the display unit Reading the Battery State-of-Charge BATTERY STATUSTurning on the Invert Function Changing the Idle Mode SettingInverter Functions To turn on the invert functionCharging Functions Summary of CHARGER STATUS LEDsTo start a charge cycle Charging the BatteriesEqualizing the Batteries WARNING Explosion HazardTo start an equalization cycle To end an equalization cycle manuallyTo change the Power Share setting Activating Power ShareBattery Capacity Testing See pageTo test battery capacity Synchronizing the Link 1000 to the Battery To synchronize the Link 1000 to the batteryOver-charge Ah Accumulation of Positive Ah Battery History To access battery historyParameters have been met since the last time it was reset to the factory defaults. A discharge of less than 10% of battery capacity is not counted as a “cycle” Code Reading Error CodesError MeaningMeaning ErrorCode AC backfeedMeaning ErrorCode E012Specifications are subject to change without notice SpecificationsElectrical and physical specifications for the Link Default settings Appendix A listsControl Panel Physical Specifications Control Panel Electrical SpecificationsControl Panel Electrical Specifications Inverter/Charger Controls Default SettingsMonitoring Functions Page Appendix B contains The warranty for your LinkProduct and System Information Instructions for returning the product for servicingWarranty Proof of purchase may be in any one of the following forms Product DisclaimerExclusions Warning Limitations On Use Return Material Authorization PolicyReturn Material Procedure Record these details in “Record of System Settings” on pageProduct Information Record of System Settings SettingSetting Index SymbolsNumerics Page