Manuals / Xantrex Technology / Lawn and Garden / Portable Generator

Xantrex Technology Link 1000 manual F14 mode The RESET and DATA LEDs are orange-yellow

Models: Link 1000

1 74

Download 74 pages 11.15 Kb

Page 42

F14 mode:

About Link 1000 Settings

F14 Test Control Panel Display

Default: Off

Range: On while the SET button is pressed when this function is active. Off when SET is released.

This function lets you confirm that the Link 1000 control panel display is operating properly. When you press SET in

F14 mode:

•The RESET and DATA LEDs are orange-yellow.

•All other LEDs display their normal color.

•The Numeric Display reads 188.8.

The display returns to normal when you release SET. Operation of the LOCK and FUNC LEDs is confirmed when power is initially applied to the Link 1000.

F15 Display Software Revision Number

•Press SET to display the Software Revision Number.

This function displays the software revision number installed in your Link 1000. Record this number on page 60 in case you need to call Customer Service.

F16 Turn on Active Temperature Compensation

Default: Off

Range: Off, On

Turn this function On if your inverter/charger has a temperature sensor.

Leave this function Off if you are not using a temperature sensor.

When this function is On, the Link 1000 uses the actual battery temperature reported to the Freedom Inverter/Charger by a Heart TC2+2 unit, the Freedom 458 or the Freedom Marine Inverter/Charger temperature sensor.

34

Image 42

Xantrex Technology Link 1000 manual F14 mode The RESET and DATA LEDs are orange-yellow

Contents

Link Owner’s GuideNotice of Copyright About XantrexTrademark DisclaimerContents 2 Installing the Link1 Introducing Link 3 Setting up the Link 4 Using the Link Index A SpecificationsB Product and System Information ContentsFigures Link 1000 Control Panel System Overview WiringBATTERY STATUS Light Bar Display Panel and Mounting Plate Link 1000 Mounting PlatePage Chapter 1 describes The features on its control panelIntroducing Link The Link 1000’s control and monitoring functionsIntroducing the Link Inverter/Charger Control FunctionsMonitoring Functions The number of deep cycles the battery has had The time remaining in your battery before it is completely dischargedBattery history including Present charge efficiency The deepest level of discharge The average level of dischargeReading the Link 1000 Control Panel Figure 1 Link 1000 Control Panel2, 3 Numeric display and display units To install the Link 1000, see page To set up the Link 1000, see page Where to go From HereIndicates that AC power is present To use the Link 1000, see pageA list of installation tools and equipment Installation procedures Installing the LinkAn overview of the installation process Chapter 2 givesPlanning the Installation Refer to Figure 2 on pageInstallation Considerations The shunt sense leads must be 18AWG twisted pair wires Installing the Link Overview of Installation StepsBattery Figure 2 System Overview WiringInstalling the Link BatteryMounting the Link 1000 Control Panel To mount the control panelMounting and Cabling the Shunt To mount and cable the shuntWiring the Terminal Block To wire the terminal blockConnecting Terminal Block Wires to Shunt and Battery To connect the terminal block wiresTesting the Installation Installing FusesConnecting the Phone Cable To install fusesMaintenance Disconnecting the Inverter/ChargerEach setting as well as the options for each setting Setting up the LinkHow to set up the Link 1000 to best suit your battery system Whether you should change settings or leave the default settingAbout Link 1000 Settings To enter Setup mode and change a valueTo lock the setup Locking Your Setup ValuesResetting Values To reset valuesBattery Capacity To change the Battery Capacity setting To change the Battery Type settingTo change the Ambient Temperature setting Changing the Ambient Temperature SettingTo change the Charged Voltage setting Charged ParametersTo change the Time Remaining setting To change the Charged Current PercentageChanging the Time Remaining Setting To change Power Share values Changing the Power Share SettingTo change the Idle mode setting Changing the Idle Mode SettingF01 Auto Display Scanning Default Off Range Off, On Advanced Function ValuesHow to Enter Setup Mode and Change a Value Reminder F02 Display Sleep Default On Range On, OffRange 30 F-120 F -1.11 C-48.8 C in 10 increments Range Off and On. On = use alternative energy defaults Default 1.25 for liquid lead-acid batteries. Battery Type set to Type Default 0 Liquid Cell F14 mode The RESET and DATA LEDs are orange-yellow Turn on the invert function Change the Idle mode setting Using the LinkChapter 4 tells you how to Read the battery’s state-of-charge Charge and equalize the batteries Determine battery capacityMonitoring Functions Choosing a Display Unit Volts, Amps, Ah, or TimeTo change the display unit Reading the Battery State-of-Charge BATTERY STATUSTurning on the Invert Function Changing the Idle Mode SettingInverter Functions To turn on the invert functionCharging Functions Summary of CHARGER STATUS LEDsTo start a charge cycle Charging the BatteriesEqualizing the Batteries WARNING Explosion HazardTo start an equalization cycle To end an equalization cycle manuallyTo change the Power Share setting Activating Power ShareBattery Capacity Testing See pageTo test battery capacity Synchronizing the Link 1000 to the Battery To synchronize the Link 1000 to the batteryOver-charge Ah Accumulation of Positive Ah Battery History To access battery historyParameters have been met since the last time it was reset to the factory defaults. A discharge of less than 10% of battery capacity is not counted as a “cycle” Code Reading Error CodesError MeaningMeaning ErrorCode AC backfeedMeaning ErrorCode E012Specifications are subject to change without notice SpecificationsElectrical and physical specifications for the Link Default settings Appendix A listsControl Panel Electrical Specifications Control Panel Physical SpecificationsControl Panel Electrical Specifications Default Settings Inverter/Charger ControlsMonitoring Functions Page Appendix B contains The warranty for your LinkProduct and System Information Instructions for returning the product for servicingWarranty Proof of purchase may be in any one of the following forms Disclaimer ProductExclusions Warning Limitations On Use Return Material Authorization PolicyReturn Material Procedure Record these details in “Record of System Settings” on pageProduct Information Record of System Settings SettingSetting Symbols IndexNumerics Page