Manuals / Xantrex Technology / Computer Equipment / Computer Monitor

Xantrex Technology manual Unpacking and Inspection, TM500A 12/24 Volt, TM500A - NS 12/24 Volt

Models: TM500A

1 44

Download 44 pages 16.27 Kb

Page 8

Image 8

1.0 INTRODUCTION

Unpacking and Inspection

Upon receiving the TM500A, check that the following items are included.

TM500A (12/24 Volt)

•TM500A (meter panel, adaptor and mounting bracket)

•Manual

•50-foot communications cable

•Deltec™ 500 amp/50 mV shunt

•12/24 volt shunt-printed circuit board with in-line 2-amp fuse

TM500A - NS (12/24 Volt)

•TM500A (meter panel, adaptor and mounting bracket)

•Manual

•50-foot communications cable

•Shunt-printed circuit board with in-line 2-amp fuse

TM48 (48 Volt)

•48-volt shunt-printed circuit board with in-line 2-amp fuse

2	© 2001 Xantrex Technology Inc.
	P/N 973-0012-01-02 Rev.A 05/01

Page 8

Image 8

Xantrex Technology Unpacking and Inspection, TM500A 12/24 Volt, TM500A - NS 12/24 Volt, TM48 48 Volt, Introduction

Contents

Battery Status Monitor Installation Operator’s Guide TM500AAbout Xantrex TrademarksNotice of Copyright DisclaimersTable of Contents 2.0 INSTALLATION3.0 CONFIGURATION 1.0 INTRODUCTIONTable of Contents 5.0 TROUBLESHOOTING6.0 SERVICE INFORMATION 7.0 SPECIFICATIONSIMPORTANT SAFETY INSTRUCTIONS BATTERY SAFETY INFORMATION SAVE THESE INSTRUCTIONS1.0 INTRODUCTION The TM500AThe TM500A 14.2Unpacking and Inspection TM500A 12/24 VoltTM500A - NS 12/24 Volt TM48 48 Volt2.0 INSTALLATION Pre-InstallationRequired Tools MountingSurface Mounting 2.0 INSTALLATIONSurface Mounting the TM500A Using the Adaptor Communication and Remote Cable Connections2.0 INSTALLATION Wire Access Hole Trace Meter Bracket Trace MeterFlush Mounting 2.0 INSTALLATIONArea To Be Cut-Out Flush Mounting the TM500A2.0 INSTALLATION Communication and Remote Cable Connections2.0 INSTALLATION Extended Length InstallationsExtended Length Ground Wire Mounting/Wiring the Shunt Deltec ShuntShunt Connections 2.0 INSTALLATIONMounting Circuit Board to an Existing Shunt NOTE Use only the hardware supplied in the kitShunt Circuit Board and Hardware 2.0 INSTALLATIONConnecting the Shunt Board Circuit DiagramIn-line Fuse 2.0 INSTALLATION3.0 CONFIGURATION SetupRestoring the Factory Defaults Resetting to Factory DefaultsSetting Parameters Setting Parameters14.4 3.0 CONFIGURATIONSetting Parameters continued Charge Efficiency % Setting the Charge Efficiency FactorSetting Charger Efficiency 3.0 CONFIGURATION3.0 CONFIGURATION Setting Parameters continued Amp Hours AhSetting the Amp Hours Setting Parameters continued Setting the Amp Hours3.0 CONFIGURATION Set Battery Amp-Hour Rating Ah LED IndicatesSetting Parameters continued CHARGED Indicator Setup Step A Setting the Fully-Charged Voltage LevelTrigger on Voltage Only 3.0 CONFIGURATIONSetting Parameters continued CHARGED Indicator Setup continued Setting the CHARGED Indicator Voltage LevelStep B Switching OFF the Amperage Detection 14.4Trigger on Voltage and Amperage 3.0 CONFIGURATIONSetting Parameters continued CHARGED Indicator Setup continued Step A Setting the Fully-Charged Voltage LevelStep B Setting the Amperage Trigger Level Trigger on Voltage and Amperage3.0 CONFIGURATION Setting Parameters continued CHARGED Indicator Setup continuedTrigger on Voltage and Time 3.0 CONFIGURATIONSetting Parameters continued CHARGED Indicator Setup continued Step A Setting the Fully-Charged Voltage LevelStep B Setting the Time Duration 1. HTrigger on Voltage and Time 3.0 CONFIGURATIONCharger Considerations Relay ChargersTaper Chargers Three-stage ChargersSetting Parameters continued Low-Voltage Indicator Configuring the Low-Voltage AlarmLow-Voltage Indicator 3.0 CONFIGURATIONIndicators and Controls RESET ButtonFront Panel Controls and Indicators 4.0 OPERATIONIndicators and Controls continued Basic Meters Meter Selection and LED Indicators12.4 Available Meters % state-of chargeIndicators and Controls continued Ah AMP HOURS Power Saving ModeMode Indicator LEDs FullIndicators and Controls continued Data Monitors bHI High Battery VoltagebLO Low Battery Voltage dSF Days Since Full4.0 OPERATION Indicators and Controls continuedTo access the Data Monitor Function Reminders and Indicators To configure this functionAmp-Hour Reminder Meter Selection and LED Indicators4.0 OPERATION Reminders and Indicators continued Low-Voltage IndicatorTo configure this alarm Reminders and Indicators continued CHARGED Indicator To reset the CHARGED LEDResetting the CHARGED Indicator 4.0 OPERATION5.0 TROUBLESHOOTING SymptomSolution Possible Cause6.0 SERVICE INFORMATION 7.0 SPECIFICATIONS SpecificationsBattery Volts Battery Amps8.0 WARRANTY Limited WarrantyPage Xantrex Technology Inc 2001 Xantrex Technology Inc5916 195th Northeast Arlington, WA