Connect an audio cable if necessary | Yamaha CRW3200NB instruction

Note

•IDE devices supporting Ultra ATA/66 or Ultra ATA/100 do not operate with the included 40-pin IDE cable. Prepare proper IDE cables for those IDE devices.

•You can use an IDE cable that supports Ultra ATA/66 to connect to the CRW3200E drive.

•Use an IDE cable no longer than 45.7 cm (18 in.).

•When two IDE devices are connected to one IDE cable, be sure to assign each as master/slave respectively.

4 Connect an audio cable if necessary.

The sound card of the computer enables you to listen to audio CDs played back on the CRW3200E drive. There are two methods to connect the CRW3200E drive and the sound card: analog connection and digital connection.

Audio CD playback

•Audio is available from the headphones or speakers connected to the headphone jack on the front panel of the CRW3200E drive (this is convenient for the computer without a sound card). In such a case, connecting an audio cable is not required.

•An audio cable is not required to extract an image file from an audio CD since data is transferred via the IDE cable.

•If the CRW3200E drive is installed as an additional drive and the CD- ROM drive or DVD-ROM drive is already connected to the sound card, Yamaha recommends that audio CDs be played back by the existing drive.

Continued on next page

18

Image 26

Yamaha CRW3200NB manual Connect an audio cable if necessary, Audio CD playback

Contents

Page FCC Information U.S.A Achtung English Safety Precautions Iii Warranty Table of Contents SafeBurn Enhanced stability writing technology Features of the CRW3200E DriveHigh speed writing/reading High fidelity digital audio Names and Functions of Parts Front Panel Rear Panel Names and Functions of Parts Copyright Precautions on UseHandling Discs Disclaimer of Indemnity CD-R discs Useable discsDiscs that can be written on CD-RW discs Partial CAV Constant Angular Velocity Image file System RequirementsComputer PC/AT compatible Operating system OS Preparing tools Preparing the CRW3200E DriveSerial Number Serial Number Decide the Installation Method Preparing the CRW3200E Drive Installing the CRW3200E drive as an additional drive Replacing an existing IDE device with the CRW3200E drive Examples of connecting the CRW3200E drive Example 1 As a secondary slave For additional drive IDE Preparing the CRW3200E Drive Set the Jumper Switch Cable Select Csel Replacing Install the CRW3200E DriveInstalling the CRW3200E drive as an additional drive Connect the included 40-pin IDE cable Connect an audio cable if necessary Audio CD playback Preparing the CRW3200E Drive Analog connection Digital connection Spdif Top Power connector Bottom When using Windows 95/98/98 Second Edition/Me Check Recognition of the CRW3200E Drive When using Windows 2000 Professional When using Windows XP When using Windows 2000 Professional/XP Check Install CD Writing Software DMA Direct Memory Access Loading/Ejecting a Disc Manually Ejecting a Disc Loading/Ejecting a Disc Troubleshooting Is the computer turned on? Is each IDE device set respectively? Disc tray does not open when you press the eject buttonIs the disc tray opened when the computer is restarted? Is any CD writing software being used? Disc is ejected without order or it comes out spontaneously No data can be read from a disc Playback of an audio CD CD-DA cannot be heard For Windows Me For Windows XP Is the power capacity of your computer sufficient? Error message Buffer Underrun is displayedOther problems Yamaha CD-R/RW Drive website FirmwareChecking the firmware version in your CRW3200E drive For Windows 95/98/98 Second Edition/Me CRW3200E Drive Specifications Supported Formats Write Read Play back *4 Data Capacity CRW3200E Drive Specifications Safety/EMC Compliance CRW3200E drive conforms to the following specifications Writing Methods Technical NotesBuffer Underrun Protection Function Disc-at-Once DAO Track-at-Once TAO Session-at-Once SAO Packet Writing Canada