63
Sending the signal from an input channel to a MIX bus
5
Input channel operations
LS9-16/32 Owner’s Manual
DPRE/POST indicator
This indicates the send position of the signal sent from
the input channel to a VARI type MIX bus. The signal
is being sent from the pre-EQ or pre-fader position if
this indicates PRE, or from immediately after the
[ON] key if the PRE indication is not shown. This
indicator is only for display. You cannot use this field
to change the send position of the signal.
3Use the LAYER section keys and the [SEL]
keys of the channel module section or ST
IN section to select the input channel that
you want to operate.
4Use the MIX/MATRIX SELECT section keys
to select the send-destination MIX bus.
The LED of the corresponding key will light, indicat-
ing that it is selected as the send-destination.
●If the send-destination MIX bus is the VARI
type
The TO MIX field in the screen shows the knob in the
same color as the corresponding key of the MIX/
MATRIX SEND section.
●If the send-destination MIX bus is the FIXED
type
The TO MIX field will show the TO MIX ON/OFF
button instead of the TO MIX LEVEL knob. In this
case, you can’t adjust the send level.
5If you selected a VARI type MIX bus in step
4, use the SELECTED CHANNEL section
[SELECTED SEND] encoder to adjust the
send level from that channel to the MIX bus
you selected in step 4.
If the send-destination MIX bus is set to stereo, the
function of the [SELECTED SEND] encoder will
change depending on which of the two adjacent keys
of the MIX/MATRIX SELECT section are lit.
●If the left key is lit
Use the [SELECTED SEND] encoder to adjust the
pan (or balance, for a ST IN channel) of the signal that
is sent from the INPUT channel to the two MIX buses.
●If the right key is lit
Use the [SELECTED SEND] encoder to adjust the
send level shared by the two MIX buses.
6To switch the on/off status of a signal sent
to a VARI type MIX bus, move the cursor to
the TO MIX LEVEL knob in the screen and
press the [ENTER] key to accsess the MIX
SEND popup window.
If you switch this off, the knob will turn grey.
7To switch the on/off status of a signal sent
to a FIXED type MIX bus, move the cursor to
the TO MIX ON/OFF button in the screen
and press the [ENTER] key.
If you switch this off, the knob will change to black
characters on a blue background. To turn it back on,
press the [ENTER] key once again.
8Use the top panel [SEL] keys to select
another input channel, and adjust the send
level to the selected MIX bus in the same
way.
9Use the keys of the MIX/MATRIX SELECT
section to select another MIX bus as the
send-destination, and adjust the send level
from the input channel in the same way.
• If the LED of only a specific key in the MIX/MATRIX SELECT
section is blinking and the LEDs of the remaining keys are lit,
the LS9 is in SENDS ON FADER mode (the mode in which
you can use the faders to control the send levels to the MIX
buses or MATRIX buses). Press the desired key in the MIX/
MATRIX SELECT section so that only the LED of that key is
lit.
NOTE
• If PRE is selected as the send position to the MIX bus, then
you will also be able to select either PRE EQ (immediately
before the attenuator) or PRE FADER (immediately before the
fader) for each MIX bus (
→
p. 213).
• If desired, the pan/balance setting of the signal sent to a ste-
reo MIX bus can be linked with the TO ST PAN/TO ST BAL
knob of the SELECTED CH VIEW screen (
→
p. 213).
•If you want to monitor the signal that is being sent to a specific
MIX bus, select the master fader layer and press the [CUE]
key for that MIX channel.
HINT