65
Sending the signal from an input channel to a MIX bus
5
Input channel operations
LS9-16/32 Owner’s Manual
GTO MIX PAN/TO MIX BALANCE knob
This knob adjusts the pan (or balance, for a ST IN
channel) of the signal that is sent from the INPUT
channel to the two MIX buses.
[ For a FIXED type MIX bus ]
1Channel number / Channel name
This indicates the number and name of the send-
source channel.
BTO MIX ON/OFF button
This is an on/off switch for the signal that is sent from
the send-source channel to the currently selected MIX
bus.
If the send-destination MIX bus is set to stereo, on/off
operations are linked for adjacent odd-numbered/even-
numbered MIX buses.
6If you selected a VARI type MIX bus in step
4, move the cursor to the TO MIX LEVEL
knob in the screen, and use the dial or the
[DEC]/[INC] keys to adjust the send level
from each channel to the selected MIX bus.
If the send-destination MIX bus is set to stereo, move
the cursor to the TO MIX PAN (TO MIX BALANCE)
knob and adjust the pan (or balance, for a ST IN chan-
nel) of the signal sent from each channel to the two
MIX buses.
7To switch the send position of a signal sent
to a VARI type MIX bus, move the cursor to
the PRE button in the screen and press the
[ENTER] key.
If the PRE button is on, the pre-EQ or pre-fader signal
will be sent; if this button is off, the signal from imme-
diately after the [ON] key will be sent.
8To switch the on/off status of a signal sent
to a VARI/FIXED type MIX bus, move the
cursor to the TO MIX ON/OFF button in the
screen and press the [ENTER] key.
If the send-destination MIX bus is set to stereo, opera-
tion of the adjacent left/right pair of buttons is linked.
9If you want to operate a channel that is not
currently shown in the popup window, use
the [SEL] key to select that channel, and
then make settings for it.
10
If you want to adjust the send level to
another MIX bus, use the keys of the MIX/
MATRIX SELECT section to select another
MIX bus, and make settings in the same
way.
11
When you’ve finished making settings,
move the cursor to the CLOSE button (or
the × symbol in the upper right of the win-
dow) and press the [ENTER] key.
Here’s how to use the top panel faders/encoders to adjust
the send level and turn the signal on/off for the signals sent
from all input channels to a specific MIX bus.
1Make sure that an output port is assigned
to the MIX bus to which you’re sending the
signal, and that a monitor system or exter-
nal effect processor etc. is connected to the
corresponding output port.
2Press the SELECTED CHANNEL section
[HOME] key.
The SELECTED CH VIEW screen will appear in the
display.
1SEND popup button
• If PRE is selected as the send position to the MIX bus, then
you will also be able to select either PRE EQ (immediately
before the attenuator) or PRE FADER (immediately before the
fader) for each MIX bus (
→
p. 213).
• If desired, the pan/balance setting of the signal sent to a ste-
reo MIX bus can be linked with the TO ST PAN/TO ST BAL
knob of the SELECTED CH VIEW screen (
→
p. 213).
HINT
2
1
• If the PRE button is on, then you will be able to select either
PRE EQ (immediately before the attenuator) or PRE FADER
(immediately before the fader) for each MIX bus (
→
p. 213).
HINT

Using the faders (SENDS ON FADER

mode)

1