Yamaha LS9-16, LS9-32 Making dynamics settings, Making HPF/EQ settings

Operations in the SELECTED CHANNEL section

LS9-16/32 Owner’s Manual

●Making dynamics settings

To operate the dynamics of the currently selected channel,

use the SELECTED CHANNEL section [DYNAMICS 1]/

[DYNAMICS 2] encoder, and the DYNA1/DYNA2 ﬁeld

of the SELECTED CH VIEW screen.

The DYNA1/DYNA2 ﬁeld of the SELECTED CH VIEW

screen contains the following items.

1DYNA1/DYNA2 popup buttons

These buttons access the DYNAMICS 1/DYNAMICS 2

popup window, where you can make detailed settings for

dynamics.

BTHRESH knob

This indicates the setting of the threshold parameter of a

gate or compressor. To adjust the value, use the

SELECTED CHANNEL section [DYNAMICS 1]/

[DYNAMICS 2] encoder. (Alternatively, move the cursor

to the knob and operate the dial or the [DEC]/[INC] keys.)

CDYNAMICS ON/OFF button

These buttons turn dynamics processors 1/2 on/off.

DOVER indicator

This will light if the output level of the dynamics reaches

the overload point.

ELevel meter

This displays a bar graph indication of the signal level

being input to the dynamics (on=green, off=gray) and the

amount of gain reduction (orange). The threshold setting

is shown as a vertical line.

FParameter knobs

These knobs indicate the values of parameters other than

threshold.

To operate the dynamics, turn the DYNAMICS ON/OFF

button on, and use the SELECTED CHANNEL section

[DYNAMICS 1]/[DYNAMICS 2] encoders to adjust the

threshold parameters. (Alternatively, move the cursor to

the DYNA1/DYNA2 ﬁeld, and operate the dial or the

[DEC]/[INC] keys.)

To make detailed dynamics settings, move the cursor to

the DYNA1/DYNA2 popup button or the DYNA1/

DYNA2 ﬁeld, and press the [ENTER] key to access the

DYNAMICS 1/DYNAMICS 2 popup window. (For

details on the popup window → p. 117)

●Making HPF/EQ settings

To operate the HPF/EQ of the currently selected channel,

use the SELECTED CHANNEL section EQ encoders,

and the EQ ﬁeld of the SELECTED CH VIEW screen.

The EQ ﬁeld of the SELECTED CH VIEW screen con-

tains the following items.

1EQ popup button

This button accesses the ATT/HPF/EQ popup window,

where you can make detailed HPF/EQ settings.

BEQ ON/OFF button

Switches the EQ on/off.

CHPF ON/OFF button

Switches the HPF on/off.

DHPF FREQ knob

Indicates the cutoff frequency of the HPF.

EOVER indicator

This will light when the post-EQ signal reaches the over-

load point.

FQ/F/G knobs

These knobs indicate the Q, F (center frequency), and G

(amount of boost/cut) settings for each band (LOW, L-

MID, H-MID, and HIGH).

To operate the EQ, switch the EQ ON/OFF button on, and

use the EQ [Q], EQ [FREQUENCY], and EQ [GAIN]

knobs of the SELECTED CHANNEL section to adjust the

Q, center frequency, and the amount of boost/cut. (Use the

EQ [HIGH], EQ [HIGH MID], EQ [LOW MID], and EQ

[LOW] keys to select the band you want to operate.)

Alternatively, move the cursor to the knobs of the EQ ﬁeld

in the screen, and use the dial or the [DEC]/[INC] keys.

To make detailed EQ settings, move the cursor to the EQ

popup button or the knobs of the EQ ﬁeld, and press the

[ENTER] key to access the ATT/HPF/EQ popup window.

(For details on the popup window → p. 115)

• The DYNA 2 ﬁeld of the SELECTED CH VIEW screen and the

[DYNAMICS 2] encoder of the SELECTED CHANNEL section are

valid only if an input channel is selected.

NOTE

• If you’ve turned on POPUP APPEARS WHEN PRESSING

KNOBS in the PREFERENCE popup window (

→

p. 194), you can

also access the above popup window by pressing the SELECTED

CHANNEL section [DYNAMICS 1]/[DYNAMICS 2] encoder.

HINT