Yamaha M7CL 2 SYSTEM REALTIME MESSAGE, 3 System Exclusive Message

MIDI Data Format
M7CL Owner’s Manual 283
Appendices
1.4 PROGRAM CHANGE (Cn)
Reception
If [Program Change ECHO] is ON, bank select messages will also be echoed
from MIDI OUT.
If SINGLE CH is selected, these messages are received if [Program Change RX]
is ON and the [Rx CH] matches. However if [OMNI] is ON, these messages are
received regardless of the channel. When these messages are received, scene
memory and effect library are recalled according to the settings of the [Program
Change Table].
Transmission
If [Program Change TX] is ON, these messages are transmitted according to the
[Program Change Table] settings when scene memory and effect library are
recalled.
If SINGLE CH is selected, these messages are transmitted on the [Tx CH]
channel.
If the recalled scene memory and effect library has been assigned to more than
one program number, the lowest-numbered program number for each MIDI
channel will be transmitted.
Program Change messages are not used for transmission to M7CL Editor
because there is no guarantee that the contents of the assignment tables will
match. (Parameter Change messages are always used.)
You can choose either MULTI MIDI CH or SINGLE CH.
If SINGLE is selected
You can choose the RX CH, OMNI CH, and TX CH.
You can choose whether a bank select message will be added.
A bank of up to 16 can be specified.
If MULTI is selected
The RX and TX channels will be the same.
The assignment table will use the settings for each MIDI channel. Bank select
messages will not be added.
You can make settings for up to sixteen MIDI channels.
2 SYSTEM REALTIME MESSAGE
2.1 TIMING CLOCK (F8)
Reception
This message is used to control effects. This message is transmitted twenty-four
times per quarter note.
Echoing of this message depends on the OTHER item in the ECHO settings.
2.2 ACTIVE SENSING (FE)
Reception
Once this message has been received, MIDI communication will be initialized
(e.g., Running Status will be cleared) if no message is received for an interval of
400 ms.
This message is not subject to echoing.
2.3 SYSTEM RESET (FF)
Reception
When this message is received, MIDI communication will be initialized (e.g.,
Running Status will be cleared).
This message is not subject to echoing.
3 System Exclusive Message
3.1 Bulk Dump
The M7CL uses the following data types for a bulk dump.
‘M’
0–300 Scene number
512 Current Data (without Recall Safe)
768 Current Data (with Recall Safe)
’S’
512 Setup Memory
513 Mixer Setting
514 Output Port
515 Monitor
516 MIDI Setting
517 Library Number
’s’
512–515 User Defined Key 1–4
516–519 User Defined Key Guest 1–4
520–523 User Defined Key Admin 1–4
524 Preference
525 User Key
526 User Key Guest
527 Preference Guest
528 Preference Admin
‘Y’
1–199 Library number
512–559 Dynamics1 Input 1–48
560–567 STIN 1L–4R
768–783 MIX 1–16
1024–1031 MATRIX 1–8
1280–1282 STEREO L,R,MONO(C)
1536–1583 Dynamics2 Input 1–48
1584–1591 STIN 1L–4R
’H’
0–199 Library number
512–559 Input 1–48, 560–567 STIN 1L–4R
’h’
0–199 Library number
768–783 MIX 1–16
1024–1031 MATRIX 1–8
1280–1282 STEREO L,R,MONO(C)
’Q’, ’q’
1–199 Library number
512–559 Input 1–48, 560–567 STIN 1L–4R
768–783 MIX 1–16
1024–1031 MATRIX 1–8
1280–1282 STEREO L,R,MONO(C)
‘F’
1–199 Library number
512–527 RACK 1A–8B
‘E’
1–199 Library number
512–515 RACK 5–8
’P’, ’C’
512 Current Data
Data is lost when you write to the preset library.
The unique header (Model ID) identifies whether the device is a M7CL.
To calculate the check sum, add the bytes starting with the byte after BYTE
COUNT (LOW) and ending with the byte before CHECK SUM, take the binary
complement, and set bit 7 to 0.
CHECK SUM = (-sum)&0x7F
Bulk Dumps can be received at any time, and can be transmitted at any time
when a Bulk Dump Request is received.
A Bulk Dump is transmitted on the [Rx CH] channel in response to a Bulk
Dump Request.
In the data portion, seven words of 8-bit data are converted into eight words of
7-bit data.
STATUS 1100nnnn Cn Program change
DATA 0nnnnnnn nn Program number (0-127)
STATUS 11111000 F8 Timing clock
STATUS 11111110 FE Active sensing
STATUS 11111111 FF System reset
Command rx/tx function
F0 43 0n 3E BB BB 11 D0 D1 D2 …
EE F7 BULK DUMP DATA rx/tx BULK DUMP
DATA
F0 43 2n 3E 11 D0 D1 D2 F7
BULK DUMP REQUEST rx BULK DUMP
REQUEST
Data name
(D0)
Data Number
(D1,2)
tx/rx function
‘M’ 0–300, 512, 768 tx/rx Scene Memory & Request
‘S’ 512–517 tx/rx Setup Memory & Request
(current setup)
‘s’ 512–528 tx/rx User Setup Memory & Request
‘Y’ 1–199, 512– tx/rx Dynamics library & Request
‘H’ 0–199, 512–559,
560-567 tx/rx Input Channel library & Request
‘h’ 0–199, 768–783,
1024–1031,
1280–1282
tx/rx Output Channel library &
Request
‘Q’ 1–199, 512– tx/rx Input Equalizer library & Request
‘q’ 1–199, 768– tx/rx Output Equalizer library &
Request
‘F’ 1–199, 512– 527 tx/rx GEQ Equalizer library & Request
‘E’ 1–199, 512– 515 tx/rx Effect library & Request
‘P’ 512 tx/rx Program change table & Request
‘C’ 512 tx/rx Control change table & Request