TROUBLESHOOTING
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, set this unit to the standby mode, unplug the power cord from the outlet, and contact the nearest authorized YAMAHA dealer or service center.
■General
Problem | Cause | Remedy | Refer to | |
|
|
| page | |
|
|
|
| |
This unit fails to turn | The power cord is not connected or the | Connect the power cord firmly. | — | |
on when STANDBY/ | plug is not completely inserted. |
|
| |
ON is pressed, or |
|
|
| |
The impedance setting is incorrect. | Set the impedance to match your speakers. | 10 | ||
enters in the standby | ||||
mode soon after the | The protection circuitry has been | Make sure all speaker wire connections on this unit | 9, 11 | |
power has been | ||||
activated. | and on all speakers are secure and that the wire for |
| ||
turned on. |
| |||
| each connection does not touch anything other than |
| ||
|
|
| ||
|
| its respective connection. |
| |
|
|
|
| |
| This unit has been exposed to a strong | Set this unit in the standby mode, disconnect the | — | |
| external electric shock (such as lightning | power cord, plug it back in after 30 seconds, then use |
| |
| and strong static electricity). | it normally. |
| |
|
|
|
| |
No sound | Incorrect input or output cable | Connect the cables properly. If the problem persists, | 9, 12 | |
| connections. | the cables may be defective. |
| |
|
|
|
| |
| Input Mode is set to DTS or ANALOG. | Select AUTO. | ||
|
|
|
| |
| No appropriate input source has been | Select an appropriate input source by pressing | 18 | |
| selected. | INPUT, then rotating VOLUME/SELECT or using |
| |
|
| the input selector buttons. |
| |
|
|
|
| |
| Speaker connections are not secure. | Secure the connections. | 9 | |
|
|
|
| |
| The volume is turned down. | Turn up the volume. | — | |
|
|
|
| |
| The sound is muted. | Press MUTE or any operation button on this unit to | 19 | |
|
| cancel mute and adjust the volume. |
| |
|
|
|
| |
| If you are playing an LD source, the | Set the Input Mode to ANALOG. | ||
| player may not output digital signals if the |
|
| |
| LD source was not digitally recorded. |
|
| |
|
|
|
| |
| The Input Mode is set to ANALOG while | Set the Input Mode to AUTO or DTS. | ||
| playing a source encoded with a DTS |
|
| |
| signal. |
|
| |
|
|
|
| |
| Signals this unit cannot reproduce are | Play a source whose signals this unit can reproduce. | — | |
| being received from a source component |
|
| |
| e.g.: a |
|
| |
|
|
|
| |
The sound suddenly | The protection circuitry has been activated | Check the speaker wires are not touching each other | — | |
goes off. | because of a short circuit, etc. | and then turn this unit back on. |
| |
|
|
|
| |
| The sleep timer has turned the unit off. | Turn on the power, and play the source again. | — | |
|
|
|
| |
| The sound is muted. | Press MUTE to cancel a mute. | 19 | |
|
|
|
| |
Only the speaker on | Incorrect cable connections. | Connect the cables properly. If the problem persists, | 9, 12 | |
one side can be |
| the cables may be defective. |
| |
heard. |
|
|
| |
Incorrect balance settings in SET MENU. | Adjust the SPEAKER LEVEL settings. | 17, 41 | ||
| ||||
|
|
|
| |
Only the center | When playing a monaural source with a |
|
| |
speaker outputs | CINEMA DSP program, the source signal |
|
| |
substantial sound. | is directed to the center channel, and the |
|
| |
| front and surround speakers output effect |
|
| |
| sounds. |
|
| |
|
|
|
|
| INFORMATION | ADDITIONAL |
|
|
|
|
|
|
| English |
|
|
|
|
51
