Husqvarna 15V2 manual Introduction, Dear customer, Travel and transport on public roads, Towing

Page 4

INTRODUCTION

Dear customer

Thank you for choosing a Husqvarna Rider. Husqvarna Riders are built to a unique design with a frontmounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency even in small or confined areas. Collected controls and a hydrostatic transmission controlled by pedals also contribute to the machine’s performance.

We hope you will find this operator’s manual very useful. By following its instructions (on operation, service, maintenance, etc.) you will significantly extend the life of the machine and even its second-hand value.

When you sell your Rider, make sure you pass on the operator’s manual to the new owner.

Travel and transport on public roads

Check the relevant road traffic regulations before driving the machine on a public road. If transporting the machine on another vehicle always use approved securing devices and make sure that the machine is securely held.

Towing

Your machine is equipped with a hydrostatic transmission and, if necessary, you should only tow the machine over short distances and at a low speed, otherwise there is a risk of damaging the transmission.

Intended use

This machine is designed solely for cutting grass on conventional lawns and other cleared and leveled ground without obstacles, as rocks, stumps etc., and, in conjunction with accessories supplied by the manufacturer even for other special tasks for which instructions are delivered with the accessory. Use in any other way is considered as contrary to the intended use. Compliance with and strict adherence to the conditions of operation, service and repair as specified by the manufacturer also constitute essential elements of the intended use.

This machine should be operated, serviced and repaired only by persons who are familiar with its particular characteristics and who are acquainted with the relevant safety procedures.

Accident prevention regulations, all other generally recognised regulations on safety and occupational medi- cine, and all road traffic regulations must be observed at all times.

Any arbitrary modifications carried out to this machine may relieve the manufacturer of liability for any resulting damage or injury.

2 – English

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Rider EnglishSvenska Contents Introduction Dear customerTravel and transport on public roads TowingGood service Serial numberExplanation of Symbols Safety Instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Throttle control Choke leverSpeed limiter Parking brakeCutting unit Lift lever for cutting unitSeat Lever for adjustment of cutting heightFuelling Before starting DrivingStarting the engine Driving Driving the machine Cutting tips Stopping the engine Release leverMaintenance Maintenance scheduleDaily Maintenance interval Hours Before start 100 200Removing the machine hoods Engine hoodFront hood Right-hand fenderAdjusting the brake Checking and adjustment of the steering wiresPoorly adjusted brakes can result in reduced braking power Checking and adjusting the choke wire Checking and adjustment of the throttle wireReplacing the fuel filter Replacing the air filter VarningChecking of the fuel pump’s air filter Check the level of the battery acidFitting the wrong spark plug type can damage the engine Inspecting the safety system Checking the tyre pressure Main fuseChecking the engine’s cooling air intake Fitting the cutting unit Observe caution to avoid trapping your handInstalling BioClip Removing the cutting unitChecking and adjusting the cutting unit’s ground pressure Adjusting the parallelism of the cutting unit Belt replacement on BioClipChecking the cutting unit’s parallelism Replacing the cutting unit beltBelt change on Combi Maintenance Service position for the cutting unit Placing in service positionMaintenance Restoring from service position Checking the blades Replacing the break-pin BioClip 90, Combi Removal of BioClip plug CombiLubrication Checking the engine’s oil levelChanging the oil Changing the oil filterChecking the transmission’s oil level Lubricating the belt adjusterGeneral lubrication Trouble Shooting Schedule Problem ProcedureService StorageWinter storage CoverTechnical Data EU declaration of conformity Only applies to Europe Pre-delivery service Service JournalWork done Work done Date, mileage, stamp, sign ´z+H-¶6-¨ English 114 01
Top Page Image Contents