Husqvarna 15V2 manual Replacing the break-pin BioClip 90, Combi, Removal of BioClip plug Combi

Page 40

MAINTENANCE

Replacing the break-pin (BioClip 90, Combi 103)

The blades are fitted with a break-pin to protect the cutting unit and its drive when colliding with obstacles. A domed, spring friction washer is fitted to each blade bolt. The washer must always be replaced with a new washer if the blade bolt is loosened. Otherwise the break-pin can break causing the blades to collide.

Only use original spare parts. A set containing a blade, break-pin and friction washer can be purchased from your dealer.

1.Put the cutting unit in the service position, see “Service position for the cutting unit\Placing in the service position”.

2.Remove the blade (2A) by removing the blade bolt with washer and friction washer (2B).

3.Remove the remains of the broken break-pin (3).

4.Make sure the contact surfaces (4) on the blade and the blade mounting are metallic clean.

5.Fit one new break-pin (5) in the blade mounting.

6.Fit the blade (6), make sure it is fitted as illustrated.

7.Fit a new friction washer (7) with the concave face turned towards the blade.

8.Fit the blade bolt with washer (8). Tightening torque 45-50 Nm (4.5-5 kpm/32-36 lbft).

Removal of BioClip plug (Combi)

To change a Combi unit from BioClip function to cutting unit with rear ejection, remove the BioClip plug located under the unit with three screws.

1.Put the unit in the service position, see “Placing in the service position”.

2.Remove the three screws holding the BioClip plug, and remove the plug.

3.Tip: Fit three full-thread screws M8x15 mm in the screw holes to protect the threads.

4.Replace the unit in normal position.

Fit the BioClip plug in the reverse order.

Service position

Removal of BioClip plug

38 – English

Image 40

Contents Rider EnglishSvenska Contents Introduction Dear customerTravel and transport on public roads TowingGood service Serial numberExplanation of Symbols Safety Instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Throttle control Choke leverSpeed limiter Parking brakeCutting unit Lift lever for cutting unitSeat Lever for adjustment of cutting heightFuelling Before starting DrivingStarting the engine Driving Driving the machine Cutting tips Stopping the engine Release leverMaintenance Maintenance scheduleDaily Maintenance interval Hours Before start 100 200Removing the machine hoods Engine hoodFront hood Right-hand fenderAdjusting the brake Checking and adjustment of the steering wiresPoorly adjusted brakes can result in reduced braking power Checking and adjusting the choke wire Checking and adjustment of the throttle wireReplacing the fuel filter Replacing the air filter VarningChecking of the fuel pump’s air filter Check the level of the battery acidFitting the wrong spark plug type can damage the engine Inspecting the safety system Checking the tyre pressure Main fuseChecking the engine’s cooling air intake Fitting the cutting unit Observe caution to avoid trapping your handInstalling BioClip Removing the cutting unitChecking and adjusting the cutting unit’s ground pressure Adjusting the parallelism of the cutting unit Belt replacement on BioClipChecking the cutting unit’s parallelism Replacing the cutting unit beltBelt change on Combi Maintenance Service position for the cutting unit Placing in service positionMaintenance Restoring from service position Checking the blades Replacing the break-pin BioClip 90, Combi Removal of BioClip plug CombiLubrication Checking the engine’s oil levelChanging the oil Changing the oil filterChecking the transmission’s oil level Lubricating the belt adjusterGeneral lubrication Trouble Shooting Schedule Problem ProcedureService StorageWinter storage CoverTechnical Data EU declaration of conformity Only applies to Europe Pre-delivery service Service JournalWork done Work done Date, mileage, stamp, sign ´z+H-¶6-¨ English 114 01