Husqvarna 15V2 manual Service Journal, Pre-delivery service, Work done

Page 48

SERVICE JOURNAL

Work done

Date, mileage, stamp, sign

Pre-delivery service

1.	Top up battery with acid and recharge for four hours.
2.	Fit steering wheel, seat and any optional equipment.
3.	Adjust cutting unit:
	Adjust the lifting springs (the “weight” of the cutting unit should
	be 12-15 kg/26,5-33 lbs). Applies to BioClip and Combi deck.
	Adjust cutting unit so that rear edge is about 2–4 mm/1/8"
	higher than front edge.
	Adjust cutting unit height setting so that cutting height limit is
	5 mm/3/16" above the frame of the unit at the lowest cutting
	height.
4.	Check that engine has correct amount of oil.
5.	Check that the right amount of oil is in the transmission.
6.	Check and adjust tyre pressure (60 kPa/0.6 bar/8.5 PSI).
7.	Connect battery.
8.	Fill with fuel and start engine.
9.	Check that machine does not move in neutral.
10. Check:
	Forward drive.
	Reverse drive.
	Operation of blades.
	Seat safety switch.
	Lift lever safety switch.
	Safety switch for the hydrostat pedals.
11. Check engine revs 2 900±100rpm.
12. Tell customer about:		Pre-delivery service carried out.
		Pre-delivery service carried out.
	Need and benefits of following the service schedule.	No outstanding problems.
		No outstanding problems.
	The need and advantages of leaving the machine for regular	Certified:
	service.
	The effects of maintenance on the machine’s second hand
	value.
	Range of applications for BioClip.
13. Complete proof of sale, etc.

After first 8 hours 1. Change engine oil.

46 – English

Image 48

Contents Rider EnglishSvenska Contents Introduction Dear customerTravel and transport on public roads TowingGood service Serial numberExplanation of Symbols Safety Instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Throttle control Choke leverSpeed limiter Parking brakeCutting unit Lift lever for cutting unitLever for adjustment of cutting height SeatFuelling Driving Before startingStarting the engine Driving Driving the machine Cutting tips Stopping the engine Release leverMaintenance Maintenance scheduleDaily Maintenance interval Hours Before start 100 200Removing the machine hoods Engine hoodFront hood Right-hand fenderChecking and adjustment of the steering wires Adjusting the brakePoorly adjusted brakes can result in reduced braking power Checking and adjustment of the throttle wire Checking and adjusting the choke wireReplacing the fuel filter Replacing the air filter VarningCheck the level of the battery acid Checking of the fuel pump’s air filterFitting the wrong spark plug type can damage the engine Inspecting the safety system Main fuse Checking the tyre pressureChecking the engine’s cooling air intake Fitting the cutting unit Observe caution to avoid trapping your handInstalling BioClip Removing the cutting unitChecking and adjusting the cutting unit’s ground pressure Adjusting the parallelism of the cutting unit Belt replacement on BioClipChecking the cutting unit’s parallelism Replacing the cutting unit beltBelt change on Combi Maintenance Service position for the cutting unit Placing in service positionMaintenance Restoring from service position Checking the blades Replacing the break-pin BioClip 90, Combi Removal of BioClip plug CombiLubrication Checking the engine’s oil levelChanging the oil Changing the oil filterLubricating the belt adjuster Checking the transmission’s oil levelGeneral lubrication Trouble Shooting Schedule Problem ProcedureService StorageWinter storage CoverTechnical Data EU declaration of conformity Only applies to Europe Service Journal Pre-delivery serviceWork done Work done Date, mileage, stamp, sign ´z+H-¶6-¨ English 114 01