Husqvarna CARB III manual Assembly

Page 19

ASSEMBLY

Fit the bar over the bar bolts. Place the bar in its rearmost position. Place the chain over the drive sprocket locate it in the groove on the bar. Begin on the top edge of the bar.

Make sure that the edges of the cutting links are facing forward on the top edge of the bar.

Mount the clutch cover and remember to fit the chain adjuster pin in the hole in the bar. Check that the drive links of the chain fit correctly over the drive sprocket and that the chain is correctly located in the groove in the bar.

Tension the chain by turning the wheel down (+). The chain should be tensioned until it does not sag from the underside of the bar.

The chain is correctly tensioned when it does not sag from the underside of the bar, but can still be turned easily by hand. Hold up the bar tip and tighten the bar knob by turning the knob clockwise.

When fitting a new chain, the chain tension has to be checked frequently until the chain is run-in. Check the chain tension regularly. A correctly tensioned chain ensures good cutting performance and long life.

115 13 80-96 Rev.3 2008-12-17

English 19

Image 19
Contents 435 435e 440e Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA You will find the following labels on your chain sawContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Muffler Stop switchCutting equipment Vibration damping systemChain General rulesCutting equipment designed to reduce kickback BarGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain 435e, 440e 435Checking chain lubrication Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Filling with chain oilNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment 435e, 440e AssemblyFitting the bar and chain 435Assembly Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageCold engine Starting and StoppingStarting and stopping StartingStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueSafe distance Tree felling techniqueLimbing Log is supported at one end. There is a high riskClearing the trunk and preparing your retreat Felling directionDirectional cuts Felling cut What is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Carburetor adjustment MaintenanceGeneral Immediately Checking the inertia brake releaseMuffler Replacing the starter cord StarterTensioning the recoil spring Replacing the return and drive springs Air filterFitting the starter Cooling system Spark plugLubricating the bar tip sprocket Needle bearing lubricationTemperature -5C 23F or colder Air Injection centrifugal cleaningWinter use Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Emission Warranty Parts List Other safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsSímbolos en la máquina Aclaracion DE LOS SimbolosSímbolos en el manual de instrucciones Etiquetas que se encuentran en la motosierra Índice IndicePrecauciones de seguridad para usuarios de Apreciado cliente Introduccion¿Qué es qué en la motosierra? ¿QUE ES QUE?Medidas a tomar antes de utilizar una motosierra nueva Instrucciones Generales DE SeguridadImportante Freno de cadena con protección contra reculadas Emplee siempre el sentido comúnEquipo de protección personal Equipo de seguridad de la máquina«TIRAR Hacia Atrás Para REINICIAR» Captor de cadena Fiador del aceleradorProtección de la mano derecha Silenciador Equipo de corteSistema amortiguador de vibraciones Botón de paradaCadena Reglas básicasEquipo de corte reductor de reculadas EspadaGeneralidades sobre el afilado de los dientes cortantes Afilado de dientes cortantes Tensado de la cadenaGeneralidades sobre el ajuste de la profundidad de corte 435 Repostaje de aceite para cadena de motosierra Lubricación del equipo de corteControl de la lubricación de la cadena ¡ATENCION! La mayoría de los Piñón de arrastre de la cadenaLubricación del cojinete de agujas Control del desgaste del equipo de corteDeben utilizarse guantes protectores MontajeMontaje de la espada y la cadena ¡ATENCION! Para manipular la cadenaMontaje del apoyo de corteza Carburante Manipulacion DEL CombustibleAlmacenamiento prolongado RepostajeSeguridad en el uso del combustible Transporte y almacenamiento¡ATENCION! Antes de arrancar, observe Lo siguiente Arranque Y ParadaArranque y parada ArranqueParada Reglas básicas de seguridad Tecnica DE TrabajoAntes de utilizar la máquina Instrucciones generales de trabajoReglas básicas Designaciones Técnica básica de corteDesramado Técnica de talaDistancia de seguridad Corte de ramas bajas y camino de retirada Dirección de derriboCorte de indicación Corte de derribo Tratamiento de una tala fallida Medidas preventivas de las reculadas¿Qué es la reculada? Tronzado del tronco Generalidades MantenimientoAjuste del carburador Detenerse inmediatamente Control de la función de inerciaSilenciador Cambio del cordón de arranque Mecanismo de arranqueTensado del muelle de retorno Cambio del muelle de retorno y el muelle de arrastre Filtro de aireMontaje del mecanismo de arranque Sistema refrigerante BujíaEngrase del cabezal de rueda de la espada Lubricación del cojinete de agujasUtilización en invierno Depuración centrífuga Air InjectionTemperaturas de -5C 23F o inferiores Programa de mantenimiento Datos técnicos Datos TecnicosAfilado y calibres de afilado de la cadena de sierra Combinaciones de espada y cadenaSUS Derechos Y Obligaciones DE Garantia Lista DE Piezas DE LA Garantía DE Emisiones Otras precauciones de seguridad Precauciones DE Seguridad DE LA Norma AmericanaPrecauciones de seguridad para usuarios de motosierras Precauciones de seguridad en reculadas115 13 80-96 Rev.3 115 13 80-96 Rev.3 ´z+SF¶6¢¨ ´z+SF¶6¢¨ 115 13 80-96 Rev.3 1151380-96