Husqvarna CARB III manual Spark plug, Lubricating the bar tip sprocket, Needle bearing lubrication

Page 37

MAINTENANCE

Spark plug

The spark plug condition is influenced by:

Incorrect carburetor adjustment.

An incorrect fuel mixture (too much or incorrect type of oil).

A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.020 inch (0.5 mm). The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly.

When lubricating, remove the clutch cover by loosening the two bar nuts. Lay the saw on its side with the clutch drum upwards.

Lubrication involves engine oil dripping into the centre of the clutch drum as it rotates.

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

1Air intake on the starter.

2Air guide plate.

3Fins on the flywheel.

4Cooling fins on the cylinder.

5Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

115 13 80-96 Rev.3 2008-12-17

English 37

Image 37
Contents 435 435e 440e Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA You will find the following labels on your chain sawContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Cutting equipment Stop switchVibration damping system MufflerCutting equipment designed to reduce kickback General rulesBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain 435e, 440e 435Which could lead to serious, even fatal injuries Chain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain Assembly435 435e, 440eAssembly Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingStarting Cold engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueLimbing Tree felling techniqueLog is supported at one end. There is a high risk Safe distanceClearing the trunk and preparing your retreat Felling directionDirectional cuts Felling cut What is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Carburetor adjustment MaintenanceGeneral Immediately Checking the inertia brake releaseMuffler Replacing the starter cord StarterTensioning the recoil spring Replacing the return and drive springs Air filterFitting the starter Lubricating the bar tip sprocket Spark plugNeedle bearing lubrication Cooling systemTemperature -5C 23F or colder Air Injection centrifugal cleaningWinter use Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Emission Warranty Parts List Safety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsSímbolos en la máquina Aclaracion DE LOS SimbolosSímbolos en el manual de instrucciones Etiquetas que se encuentran en la motosierra Índice IndicePrecauciones de seguridad para usuarios de Apreciado cliente Introduccion¿Qué es qué en la motosierra? ¿QUE ES QUE?Medidas a tomar antes de utilizar una motosierra nueva Instrucciones Generales DE SeguridadImportante Equipo de protección personal Emplee siempre el sentido comúnEquipo de seguridad de la máquina Freno de cadena con protección contra reculadas«TIRAR Hacia Atrás Para REINICIAR» Captor de cadena Fiador del aceleradorProtección de la mano derecha Sistema amortiguador de vibraciones Equipo de corteBotón de parada SilenciadorEquipo de corte reductor de reculadas Reglas básicasEspada CadenaGeneralidades sobre el afilado de los dientes cortantes Afilado de dientes cortantes Tensado de la cadenaGeneralidades sobre el ajuste de la profundidad de corte 435 Repostaje de aceite para cadena de motosierra Lubricación del equipo de corteControl de la lubricación de la cadena Lubricación del cojinete de agujas Piñón de arrastre de la cadenaControl del desgaste del equipo de corte ¡ATENCION! La mayoría de losMontaje de la espada y la cadena Montaje¡ATENCION! Para manipular la cadena Deben utilizarse guantes protectoresMontaje del apoyo de corteza Carburante Manipulacion DEL CombustibleSeguridad en el uso del combustible RepostajeTransporte y almacenamiento Almacenamiento prolongadoArranque y parada Arranque Y ParadaArranque ¡ATENCION! Antes de arrancar, observe Lo siguienteParada Antes de utilizar la máquina Tecnica DE TrabajoInstrucciones generales de trabajo Reglas básicas de seguridadReglas básicas Designaciones Técnica básica de corteDesramado Técnica de talaDistancia de seguridad Corte de ramas bajas y camino de retirada Dirección de derriboCorte de indicación Corte de derribo Tratamiento de una tala fallida Medidas preventivas de las reculadas¿Qué es la reculada? Tronzado del tronco Generalidades MantenimientoAjuste del carburador Detenerse inmediatamente Control de la función de inerciaSilenciador Cambio del cordón de arranque Mecanismo de arranqueTensado del muelle de retorno Cambio del muelle de retorno y el muelle de arrastre Filtro de aireMontaje del mecanismo de arranque Engrase del cabezal de rueda de la espada BujíaLubricación del cojinete de agujas Sistema refrigeranteUtilización en invierno Depuración centrífuga Air InjectionTemperaturas de -5C 23F o inferiores Programa de mantenimiento Datos técnicos Datos TecnicosAfilado y calibres de afilado de la cadena de sierra Combinaciones de espada y cadenaSUS Derechos Y Obligaciones DE Garantia Lista DE Piezas DE LA Garantía DE Emisiones Precauciones de seguridad para usuarios de motosierras Precauciones DE Seguridad DE LA Norma AmericanaPrecauciones de seguridad en reculadas Otras precauciones de seguridad115 13 80-96 Rev.3 115 13 80-96 Rev.3 ´z+SF¶6¢¨ ´z+SF¶6¢¨ 115 13 80-96 Rev.3 1151380-96