Husqvarna CARB III manual Starting and Stopping, Starting and stopping, Cold engine

Page 22

STARTING AND STOPPING

Starting and stopping

WARNING! Note the following before

!starting:

The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting.

Never start a chain saw unless the bar, chain and all covers are fitted correctly. Otherwise the clutch can come loose and cause personal injuries.

Place the machine on firm ground. Make sure you have a secure footing and that the chain cannot touch anything.

Keep people and animals well away from the working area.

Never wrap the starter cord around your hand.

Starting

The chain brake should be activated when starting the chain saw. Activate the chain brake by pushing the front hand guard forwards.

Cold engine

Start position (1): Set the start/stop switch in the choke position by pulling the red control outward - upward.

Air purge (2): Press the air purge diaphragm repeatedly until fuel fills the diaphragm (at least 6 times). The diaphragm need not be completely filled.

Push down the red choke control (4): As soon as the engine fires which can be heard through a "puff" sound, push down on the red choke control.

Pull the starter handle (5): Keep on pulling the cord powerfully until the engine starts.

Warm engine

Start position (1): The correct choke/start throttle setting for warm starting is obtained by initially moving the choke control by pulling the red control outward - upwards.

Air purge (2): Press the air purge diaphragm repeatedly until fuel fills the diaphragm (at least 6 times). The diaphragm need not be completely filled.

Push down the red choke control (4): This inactivates the choke, which is not needed when starting a warm chain saw. However the movement of the start/stop switch will have engaged a high idle, making warm starting easier.

Pull the starter handle (5): Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle.

Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull firmly and rapidly until the engine fires.

As the chain brake is still engaged the speed of the engine must be set to idling as soon as possible, this is achieved by disengaging the throttle lock. Disengagement is done by gently touching on the throttle trigger. This prevents unnecessary wear to the clutch, clutch drum and brake band. Allow the machine to idle a few seconds before giving full throttle.

2

A

1

Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle.

Pull the starter handle (3): Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull firmly and rapidly until the engine fires.

There is a simplified start reminder with illustrations to describe each step on the rear edge of the saw (A).

22 – English

115 13 80-96 Rev.3 2008-12-17

Image 22
Contents 435 435e 440e Symbols on the machine KEY to SymbolsSymbols in the operator’s manual You will find the following labels on your chain saw EPAContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping system Stop switchCutting equipment MufflerBar General rulesCutting equipment designed to reduce kickback ChainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain 435 435e, 440eFilling with chain oil Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment 435 AssemblyFitting the bar and chain 435e, 440eAssembly Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageStarting Starting and StoppingStarting and stopping Cold engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLog is supported at one end. There is a high risk Tree felling techniqueLimbing Safe distanceClearing the trunk and preparing your retreat Felling directionDirectional cuts Felling cut What is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Carburetor adjustment MaintenanceGeneral Checking the inertia brake release ImmediatelyMuffler Replacing the starter cord StarterTensioning the recoil spring Replacing the return and drive springs Air filterFitting the starter Needle bearing lubrication Spark plugLubricating the bar tip sprocket Cooling systemTemperature -5C 23F or colder Air Injection centrifugal cleaningWinter use Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesYour Warranty Rights and Obligations Emission Warranty Parts List Kickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsSímbolos en la máquina Aclaracion DE LOS SimbolosSímbolos en el manual de instrucciones Etiquetas que se encuentran en la motosierra Índice IndicePrecauciones de seguridad para usuarios de Introduccion Apreciado cliente¿QUE ES QUE? ¿Qué es qué en la motosierra?Medidas a tomar antes de utilizar una motosierra nueva Instrucciones Generales DE SeguridadImportante Equipo de seguridad de la máquina Emplee siempre el sentido comúnEquipo de protección personal Freno de cadena con protección contra reculadas«TIRAR Hacia Atrás Para REINICIAR» Captor de cadena Fiador del aceleradorProtección de la mano derecha Botón de parada Equipo de corteSistema amortiguador de vibraciones SilenciadorEspada Reglas básicasEquipo de corte reductor de reculadas CadenaGeneralidades sobre el afilado de los dientes cortantes Afilado de dientes cortantes Tensado de la cadenaGeneralidades sobre el ajuste de la profundidad de corte 435 Repostaje de aceite para cadena de motosierra Lubricación del equipo de corteControl de la lubricación de la cadena Control del desgaste del equipo de corte Piñón de arrastre de la cadenaLubricación del cojinete de agujas ¡ATENCION! La mayoría de los¡ATENCION! Para manipular la cadena MontajeMontaje de la espada y la cadena Deben utilizarse guantes protectoresMontaje del apoyo de corteza Manipulacion DEL Combustible CarburanteTransporte y almacenamiento RepostajeSeguridad en el uso del combustible Almacenamiento prolongadoArranque Arranque Y ParadaArranque y parada ¡ATENCION! Antes de arrancar, observe Lo siguienteParada Instrucciones generales de trabajo Tecnica DE TrabajoAntes de utilizar la máquina Reglas básicas de seguridadReglas básicas Técnica básica de corte DesignacionesDesramado Técnica de talaDistancia de seguridad Corte de ramas bajas y camino de retirada Dirección de derriboCorte de indicación Corte de derribo Tratamiento de una tala fallida Medidas preventivas de las reculadas¿Qué es la reculada? Tronzado del tronco Generalidades MantenimientoAjuste del carburador Control de la función de inercia Detenerse inmediatamenteSilenciador Cambio del cordón de arranque Mecanismo de arranqueTensado del muelle de retorno Cambio del muelle de retorno y el muelle de arrastre Filtro de aireMontaje del mecanismo de arranque Lubricación del cojinete de agujas BujíaEngrase del cabezal de rueda de la espada Sistema refrigeranteUtilización en invierno Depuración centrífuga Air InjectionTemperaturas de -5C 23F o inferiores Programa de mantenimiento Datos Tecnicos Datos técnicosCombinaciones de espada y cadena Afilado y calibres de afilado de la cadena de sierraSUS Derechos Y Obligaciones DE Garantia Lista DE Piezas DE LA Garantía DE Emisiones Precauciones de seguridad en reculadas Precauciones DE Seguridad DE LA Norma AmericanaPrecauciones de seguridad para usuarios de motosierras Otras precauciones de seguridad115 13 80-96 Rev.3 115 13 80-96 Rev.3 ´z+SF¶6¢¨ ´z+SF¶6¢¨ 115 13 80-96 Rev.3 1151380-96