Husqvarna CARB III manual Sharpening your chain and adjusting depth gauge setting

Page 13

GENERAL SAFETY PRECAUTIONS

Number of drive links. The number of drive links is determined by the length of the bar, the chain pitch and the number of teeth on the bar tip sprocket.

Bar groove width (inches/mm). The groove in the bar must match the width of the chain drive links.

Chain oil hole and hole for chain tensioner. The bar must be matched to the chain saw design.

Chain

Chain pitch (inches)

Drive link width (mm/inches)

Number of drive links.

Sharpening your chain and adjusting depth gauge setting

General information on sharpening cutting teeth

Never use a blunt chain. When the chain is blunt you have to exert more pressure to force the bar through the wood and the chips will be very small. If the chain is very blunt it will produce wood powder and no chips or shavings.

A sharp chain eats its way through the wood and produces long, thick chips or shavings.

The cutting part of the chain is called the cutter and consists of a cutting tooth (A) and the depth gauge (B). The cutters cutting depth is determined by the difference in height between the two (depth gauge setting).

When you sharpen a cutting tooth there are four important factors to remember.

1Filing angle

2Cutting angle

3File position

4Round file diameter

It is very difficult to sharpen a chain correctly without the right equipment. We recommend that you use our file gauge. This will help you obtain the maximum kickback reduction and cutting performance from your chain.

See instructions under the heading Technical data for information about sharpening your chain.

WARNING! Departure from the

! sharpening instructions considerably

increases the risk of kickback.

115 13 80-96 Rev.3 2008-12-17

English 13

Image 13
Contents 435 435e 440e Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA You will find the following labels on your chain sawContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Cutting equipment Stop switchVibration damping system MufflerCutting equipment designed to reduce kickback General rulesBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain 435e, 440e 435Which could lead to serious, even fatal injuries Chain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain Assembly435 435e, 440eAssembly Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingStarting Cold engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueLimbing Tree felling techniqueLog is supported at one end. There is a high risk Safe distanceClearing the trunk and preparing your retreat Felling directionDirectional cuts Felling cut What is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Carburetor adjustment MaintenanceGeneral Immediately Checking the inertia brake releaseMuffler Replacing the starter cord StarterTensioning the recoil spring Replacing the return and drive springs Air filterFitting the starter Lubricating the bar tip sprocket Spark plugNeedle bearing lubrication Cooling systemTemperature -5C 23F or colder Air Injection centrifugal cleaningWinter use Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Emission Warranty Parts List Safety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsSímbolos en la máquina Aclaracion DE LOS SimbolosSímbolos en el manual de instrucciones Etiquetas que se encuentran en la motosierra Índice IndicePrecauciones de seguridad para usuarios de Apreciado cliente Introduccion¿Qué es qué en la motosierra? ¿QUE ES QUE?Medidas a tomar antes de utilizar una motosierra nueva Instrucciones Generales DE SeguridadImportante Equipo de protección personal Emplee siempre el sentido comúnEquipo de seguridad de la máquina Freno de cadena con protección contra reculadas«TIRAR Hacia Atrás Para REINICIAR» Captor de cadena Fiador del aceleradorProtección de la mano derecha Sistema amortiguador de vibraciones Equipo de corteBotón de parada SilenciadorEquipo de corte reductor de reculadas Reglas básicasEspada CadenaGeneralidades sobre el afilado de los dientes cortantes Afilado de dientes cortantes Tensado de la cadenaGeneralidades sobre el ajuste de la profundidad de corte 435 Repostaje de aceite para cadena de motosierra Lubricación del equipo de corteControl de la lubricación de la cadena Lubricación del cojinete de agujas Piñón de arrastre de la cadenaControl del desgaste del equipo de corte ¡ATENCION! La mayoría de losMontaje de la espada y la cadena Montaje¡ATENCION! Para manipular la cadena Deben utilizarse guantes protectoresMontaje del apoyo de corteza Carburante Manipulacion DEL CombustibleSeguridad en el uso del combustible RepostajeTransporte y almacenamiento Almacenamiento prolongadoArranque y parada Arranque Y ParadaArranque ¡ATENCION! Antes de arrancar, observe Lo siguienteParada Antes de utilizar la máquina Tecnica DE TrabajoInstrucciones generales de trabajo Reglas básicas de seguridadReglas básicas Designaciones Técnica básica de corteDesramado Técnica de talaDistancia de seguridad Corte de ramas bajas y camino de retirada Dirección de derriboCorte de indicación Corte de derribo Tratamiento de una tala fallida Medidas preventivas de las reculadas¿Qué es la reculada? Tronzado del tronco Generalidades MantenimientoAjuste del carburador Detenerse inmediatamente Control de la función de inerciaSilenciador Cambio del cordón de arranque Mecanismo de arranqueTensado del muelle de retorno Cambio del muelle de retorno y el muelle de arrastre Filtro de aireMontaje del mecanismo de arranque Engrase del cabezal de rueda de la espada BujíaLubricación del cojinete de agujas Sistema refrigeranteUtilización en invierno Depuración centrífuga Air InjectionTemperaturas de -5C 23F o inferiores Programa de mantenimiento Datos técnicos Datos TecnicosAfilado y calibres de afilado de la cadena de sierra Combinaciones de espada y cadenaSUS Derechos Y Obligaciones DE Garantia Lista DE Piezas DE LA Garantía DE Emisiones Precauciones de seguridad para usuarios de motosierras Precauciones DE Seguridad DE LA Norma AmericanaPrecauciones de seguridad en reculadas Otras precauciones de seguridad115 13 80-96 Rev.3 115 13 80-96 Rev.3 ´z+SF¶6¢¨ ´z+SF¶6¢¨ 115 13 80-96 Rev.3 1151380-96