Husqvarna CARB III manual General Safety Precautions, Before using a new chain saw

Page 7

GENERAL SAFETY PRECAUTIONS

Before using a new chain saw

Please read this manual carefully.

Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly.

Refuel and start the chain saw. See the instructions under the headings Fuel Handling and Starting and Stopping.

Do not use the chain saw until sufficient chain oil has reached the chain. See instructions under the heading Cutting equipment.

Long-term exposure to noise can result in permanent hearing impairment. So always use approved hearing protection.

WARNING! Under no circumstances may ! the design of the machine be modified

without the permission of the manufacturer. Always use genuine accessories. Non-authorized modifications and/or accessories can result in serious personal injury or the death of the operator or others. Your warranty may not cover damage or liability caused by the use of non- authorized accessories or replacement parts.

WARNING! A chain saw is a dangerous ! tool if used carelessly or incorrectly and

can cause serious, even fatal injuries. It is very important that you read and understand the contents of this operator’s manual.

WARNING! The inside of the muffler ! contain chemicals that may be

carcinogenic. Avoid contact with these elements in the event of a damaged muffler.

WARNING! Long term inhalation of the ! engine’s exhaust fumes, chain oil mist and dust from sawdust can represent a

health risk.

WARNING! The ignition system of this ! machine produces an electromagnetic

field during operation. This field may under some circumstances interfere with pacemakers. To reduce the risk of serious or fatal injury, we recommend persons with pacemakers to consult their physician and the pacemaker manufacturer before operating this machine.

WARNING! Never allow children to use or ! be in the vicinity of the machine. As the

machine is equipped with a spring- loaded stop switch and can be started by low speed and force on the starter handle, even small children under some circumstances can produce the force necessary to start the machine. This can mean a risk of serious personal injury. Therefore remove the spark plug cap when the machine is not under close supervision.

Important

IMPORTANT!

The machine is only designed for cutting wood.

You should only use the saw with the bar and chain combinations we recommend in the chapter Technical data.

Never use the machine if you are fatigued, while under the influence of alcohol or drugs, medication or anything that could affect your vision, alertness, coordination or judgement.

Wear personal protective equipment. See instructions under the heading Personal protective equipment.

Do not modify this product or use it if it appears to have been modified by others.

Never use a machine that is faulty. Carry out the checks, maintenance and service instructions described in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists. See instructions under the heading Maintenance.

Never use any accessories other than those recommended in this manual. See instructions under the headings Cutting equipment and Technical data.

CAUTION! Always wear protective glasses or a face visor to reduce the risk of injury from thrown objects. A chain saw is capable of throwing objects, such as wood chips, small pieces of wood, etc, at great force. This can result in serious injury, especially to the eyes.

WARNING! Running an engine in a ! confined or badly ventilated area can

result in death due to asphyxiation or carbon monoxide poisoning.

WARNING! Faulty cutting equipment or ! the wrong combination of bar and saw

chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data.

115 13 80-96 Rev.3 2008-12-17

English 7

Image 7
Contents 435 435e 440e Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA You will find the following labels on your chain sawContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Muffler Stop switchCutting equipment Vibration damping systemChain General rulesCutting equipment designed to reduce kickback BarGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain 435e, 440e 435Checking chain lubrication Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Filling with chain oilNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment 435e, 440e AssemblyFitting the bar and chain 435Assembly Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageCold engine Starting and StoppingStarting and stopping StartingStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueSafe distance Tree felling techniqueLimbing Log is supported at one end. There is a high riskClearing the trunk and preparing your retreat Felling directionDirectional cuts Felling cut What is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Carburetor adjustment MaintenanceGeneral Immediately Checking the inertia brake releaseMuffler Replacing the starter cord StarterTensioning the recoil spring Replacing the return and drive springs Air filterFitting the starter Cooling system Spark plugLubricating the bar tip sprocket Needle bearing lubricationTemperature -5C 23F or colder Air Injection centrifugal cleaningWinter use Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Emission Warranty Parts List Other safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsSímbolos en la máquina Aclaracion DE LOS SimbolosSímbolos en el manual de instrucciones Etiquetas que se encuentran en la motosierra Índice IndicePrecauciones de seguridad para usuarios de Apreciado cliente Introduccion¿Qué es qué en la motosierra? ¿QUE ES QUE?Medidas a tomar antes de utilizar una motosierra nueva Instrucciones Generales DE SeguridadImportante Freno de cadena con protección contra reculadas Emplee siempre el sentido comúnEquipo de protección personal Equipo de seguridad de la máquina«TIRAR Hacia Atrás Para REINICIAR» Captor de cadena Fiador del aceleradorProtección de la mano derecha Silenciador Equipo de corteSistema amortiguador de vibraciones Botón de paradaCadena Reglas básicasEquipo de corte reductor de reculadas EspadaGeneralidades sobre el afilado de los dientes cortantes Afilado de dientes cortantes Tensado de la cadenaGeneralidades sobre el ajuste de la profundidad de corte 435 Repostaje de aceite para cadena de motosierra Lubricación del equipo de corteControl de la lubricación de la cadena ¡ATENCION! La mayoría de los Piñón de arrastre de la cadenaLubricación del cojinete de agujas Control del desgaste del equipo de corteDeben utilizarse guantes protectores MontajeMontaje de la espada y la cadena ¡ATENCION! Para manipular la cadenaMontaje del apoyo de corteza Carburante Manipulacion DEL CombustibleAlmacenamiento prolongado RepostajeSeguridad en el uso del combustible Transporte y almacenamiento¡ATENCION! Antes de arrancar, observe Lo siguiente Arranque Y ParadaArranque y parada ArranqueParada Reglas básicas de seguridad Tecnica DE TrabajoAntes de utilizar la máquina Instrucciones generales de trabajoReglas básicas Designaciones Técnica básica de corteDesramado Técnica de talaDistancia de seguridad Corte de ramas bajas y camino de retirada Dirección de derriboCorte de indicación Corte de derribo Tratamiento de una tala fallida Medidas preventivas de las reculadas¿Qué es la reculada? Tronzado del tronco Generalidades MantenimientoAjuste del carburador Detenerse inmediatamente Control de la función de inerciaSilenciador Cambio del cordón de arranque Mecanismo de arranqueTensado del muelle de retorno Cambio del muelle de retorno y el muelle de arrastre Filtro de aireMontaje del mecanismo de arranque Sistema refrigerante BujíaEngrase del cabezal de rueda de la espada Lubricación del cojinete de agujasUtilización en invierno Depuración centrífuga Air InjectionTemperaturas de -5C 23F o inferiores Programa de mantenimiento Datos técnicos Datos TecnicosAfilado y calibres de afilado de la cadena de sierra Combinaciones de espada y cadenaSUS Derechos Y Obligaciones DE Garantia Lista DE Piezas DE LA Garantía DE Emisiones Otras precauciones de seguridad Precauciones DE Seguridad DE LA Norma AmericanaPrecauciones de seguridad para usuarios de motosierras Precauciones de seguridad en reculadas115 13 80-96 Rev.3 115 13 80-96 Rev.3 ´z+SF¶6¢¨ ´z+SF¶6¢¨ 115 13 80-96 Rev.3 1151380-96