Makita instruction manual Technical data DCS 330 TH, Approved bar and chain combinations

Page 17

Technical data

DCS 330 TH

Single-cylinder two-stroke

 

Piston displacement

1.96 cu. in (32.3 cm3)

Cylinder bore

1.45" (37 mm)

Piston stroke

1.18" (30 mm)

Max. power at speed

1.0 / 7,000 kW/rpm

Max. torque at speed

1.45 / 5,800 Nm/rpm

Idling speed / max. engine speed with bar and chain

2,800 rpm / 11,000 rpm

Sound Pressure Level at the operator’s ear

 

at full load according to ANSI B 175.1

100 db(A)

Sound Pressure Level at the bystander’s position

 

(50ft/15 m distance) according to ANSI B 175.1

76 db(A)

Ignition system

 

Electronic, without breaker

 

Spark plug

CHAMPION RCJ 8

or Spark plug

NGK BMR 6A

Electrode gap

.020" (0.5 mm)

Fuel system

 

Carburetor

WALBRO WT with limiter caps

(all position diaphragm carburetor

 

with integral fuel pump)

 

Fuel tank capacity

8.8 oz. (0.25 l)

Fuel mixture

see chapter "Fuel"

Weight

 

without cutting attachment

7 lbs. 15 oz. (3.6 kg)

Cutting attachment

 

Guide bar

sprocket nose bar

Cutting length

14" (35 cm)

Safety saw chain (pitch)

3/8

Drive link gauge

.050

Chain sprocket

6 teeth

Chain lubrication

fully automatic oil pump (variable-flow)

Oil tank capacity

5.6 oz. (0.16 l)

 

 

Approved bar and chain combinations

"Low-kickback saw chain is a chain which has met the kickback performance requirements of ANSI B 175.1- 1991 (American National Standard for Power Tools- Gasoline-Powered Chain Saws-Safety Requirements) when tested on the representative sample of chain saws below 3.8. C.l.D. specifed in ANSI B 175.1- 1991". The approved bar and chain combinations are low kickback chains according to ANSI B 175.1-1991 and also meet the kickback requirements of CSA Z62.3-96 for chain saws below 80 cm3.

The chain saw DCS 330 TH has been approved with following guide bar and chain combinations:

Drive link gauge .050"

MAKITA:

Guide bar 3/8"

Saw chain 3/8"

length

Part no.

Part no.

14" (35 cm)

1682473

91VG-52E

OREGON:

Guide bar 3/8"

Saw chain 3/8"

length

Part no.

Part no.

14" (35 cm)

140SDEA041

91VG-52E

"There may be other replacement bar and chain combi- nations available that also reduces the risk of injury from kickback".

WARNING

Do not use other replacement bars and chains unless they have been designated as meeting the ANSI B 175.1-1991 (for USA) and CSA Z62.3-96 (for Canada) kickback performance requirements on that specific powerhead, or has been desig- nated as "low kickback" saw chain in accordance with the ANSI B 175.1-1991 (for USA) and CSA Z62.3-96 (for Canada) standard.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Owner’s Safety Manual Makita DCS 330 TH ContentsSymbols Case one of the parts listed should not be includedEngine stop switch Delivery inventoryAdditional safety precautions Safety precautions for chain saw operatorsPhysical Condition General Safety PrecautionsOperator Saw Proper clothingUse of the saw Transporting the chain sawFeet Chain saw operating instructionsFueling Fueling instructionsCutting instructions Important adjustmentsWorking conditions Reactive forces during the cut, including kickback KickbackTo avoid kickback Saw chain cutter sharpnessSpeed of contact at which the cutter contacts the object Depth gaugesPushback Cutting techniquesTo avoid pushback To avoid pull-in= cutting down area Felling instructionsSectioning Method Plunge-Cut MethodBucking LimbingMaintaining and storing the saw Maintenance and RepairDenomination of components Approved bar and chain combinations Technical data DCS 330 THMounting the guide bar and saw chain StopTightening the saw chain Checking the chain tension Chain brakeEngaging the chain brake braking Releasing the chain brakeChain oil FuelFuel mixture Correct mixture ratioWaste oil Clean screw cap and tank after refuellingRefuelling Important note on bio-degradable chain oilsChecking the chain lubrication Adjusting the chain lubricationCold start Starting the engineWarm start Stopping the engineChecking the chain brake Adjusting the carburetorImportant information Set idle speed stepMin Sharpening the saw chain Stop65 mm 025 Files and how to work with them Cleaning the guide bar, lubricating the sprocket nose Cleaning the brake band and sprocket interiorReplacing the suction head Cleaning the air filter StopReplacing the saw chain Replacing the starter cable Replacing the spark plugElectrode gap Checking the ignition sparkReplacing the return spring Cleaning the muffler / spark arrester screenCleaning the cylinder space Maintenance and repair Instructions for daily and periodic maintenanceService, spare parts and guarantee Guarantee TroubleshootingSpare parts Malfunction System Observation CauseDCS 330 TH Extract from the spare parts listFor your notes Ce produit est en conformité avec SommaireSi un des composants indiqués ici ne devait pas être SymbolesEtendue de la fourniture Mesures de sé curité supplé mentaires Condition physique Mesures gé né rales de sé curité’utilisateur La tronç onneuse Quels vê tements porter?Utilisation de la tronç onneuse Transport de la tronç onneuseDé marrage Ravitaillement en carburantInstructions de ravitaillement Instructions de coupe Ré glages importantsConditions de travail Choc de recul Kickback Les limiteurs de profondeurs Affû tage des plaquettes de coupe de la chaînePour é viter le choc de recul Le recul Techniques de coupePour é viter le recul Pour é viter la traction= zone d’abattage Instructions d’abattageMé thode de coupe en plongé e Mé thode de sectionnementDé bitage EbranchageEntretien et stockage de la tronç onneuse Entretien et ré parationLevier de gaz Bouton de blocage pour mi-gaz Dé signation des piè cesCombinaisons autorisé es de guides et de chaînes Caracté ristiques techniques DCS 330 THMontage du rail-guide et de la chaîne de sciage Mise EN RouteRemarque Tendre la chaîne de sciageContrô le de la tension de la chaîne Frein de chaîneEnclencher le frein de chaîne bloquer Libé rer le frein à mainHuile de chaîne de sciage CarburantsMé lange carburant Ré alisation du rapport correct du mé langeRemarque importante pour les huiles de chaîne De sciage bio Huile Usagé eRemplissage des ré servoirs Vé rifier le graissage de la chaîne Ré glage du graissage de la chaîneEffectuer que si le moteur est arrê té ! Stop RemarqueDé marrage à froid Dé marrer le moteurDé marrage à chaud Arrê ter le moteurRé glage du carburateur Vé rifier le frein de chaîneInformation importante Ré glage du ralenti marche à vide point65 mm Affû tage de la chaîne De sciageLime et guidage de la lime Nettoyer le guide-chaîne Regraisser l’é toile de dé viation Nouvelle chaîne de sciage Remplacement de la cré pine d’aspirationNettoyage du filtre d’air Stop Ne pas nettoyer le filtre à air à l’essenceRemplacement du cordon de lancement Remplacement de bougieEcartement des é lectrodes Vé rification de l’é tincelle d’allumageNettoyer le silencieux / du pare-é tincelles Remplacement du ressort de rappelNettoyer l’inté rieur du cylindre Risque de blesssure! Un ressort cassé peut sauterMaintenance et ré parations Service d’atelier, piè ces de rechange et garantieIndications de maintenance et d’entretien pé riodiques Garantie Piè ces de rechangeRecherche de pannes Panne Systè me Observation OrigineExtrait de la liste des piè ces de rechange Notas USA Makita U.S.A., Inc Makita Canada Inc

DCS 330 TH specifications

The Makita DCS 330 TH is a powerful and versatile chainsaw designed for professional users who demand high performance and reliability in their tools. This model is particularly favored for its exceptional cutting capabilities, making it an ideal choice for both forestry applications and general landscaping tasks.

One of the standout features of the Makita DCS 330 TH is its robust 32.2 cc 2-stroke engine, which delivers impressive power for cutting through various types of wood. With an engine speed of up to 12,000 RPM, this chainsaw can tackle thick branches and logs with ease, allowing the user to complete their tasks efficiently. The combination of power and lightweight design ensures that users can handle the saw comfortably for extended periods without excessive fatigue.

The chainsaw is equipped with a 12-inch guide bar, which enables precise cutting while maintaining a manageable size for various applications. This length strikes an optimal balance between maneuverability and cutting depth, making the DCS 330 TH an excellent choice for both pruning and felling small to medium-sized trees.

The Makita DCS 330 TH also incorporates advanced technologies that enhance its performance and user experience. One of these technologies is the automatic oil pump, which ensures that the chain is adequately lubricated during operation. This feature not only prolongs the life of the chain and bar but also enhances cutting efficiency and safety.

User comfort is further prioritized through the inclusion of an anti-vibration system that minimizes the impact of vibration during operation. This system significantly reduces user fatigue and allows for more precise control, making it easier to perform detailed cutting tasks.

Safety features are also a prominent aspect of the Makita DCS 330 TH. The chainsaw is designed with a chain brake system that quickly halts the chain in case of kickback, providing an additional layer of protection for the operator. Additionally, the tool's throttle lock ensures that the saw remains stable during operation, preventing accidental starts.

In summary, the Makita DCS 330 TH is a highly capable chainsaw that combines power, comfort, and safety features into one reliable package. Its lightweight design, advanced technologies, and user-friendly characteristics make it an excellent choice for anyone looking to invest in a quality chainsaw for demanding applications.
Top Page Image Contents