Makita DCS 330 TH Important adjustments, Working conditions, Cutting instructions

Page 8

Important adjustments

WARNING!

At correct idle speed, chain should not turn. For di- rections to adjust idle speed, see the appropriate section of this instruction manual.

Do not use a saw with incorrect idle speed adjust- ment. Adjust the idle speed yourself according to the appropriate section of this manual.

Have your MAKITA dealer check your saw and make proper adjustments or repairs.

Check the saw chain tension frequently, especially just after installing a new chain. New chains may stretch more during their initial use. A properly ad- justed saw chain can be pulled freely around the guide bar by hand without sagging. Always stop the engine and wear gloves when checking or adjusting the chain tension.

Working conditions

Operate your chain saw only outdoors. Operate the saw under good visibility and daylight conditions only.

WARNING!

Take extreme care in wet and freezing weather (rain, snow, ice). Put off the work when the weather is windy, stormy or rainfall is heavy. Clear the area where you are working.

WARNING!

Avoid stumbling on obstacles such as stumps, roots or rocks and watch out for holes or ditches. Be extremely cautious when working on slopes or un- even ground. There is increased danger of slipping on freshly debarked logs.

Cutting instructions

Always hold the saw firmly with both hands when the engine is running. Place your left hand on the tubular handle and your right hand on grip and throttle lever. Left-handers should follow these instructions too.

7

Wrap your fingers tightly around the handles, keeping the handles cradled between your thumb and forefinger (fig. 7). With your hands in this position, you can best oppose and absorb the push, pull and kickback forces of your saw without having it slip out of your grip (see section of reactive forces). Make sure your chain saw handle and grip are in good condition and free of moisture, pitch, oil or grease.

Always start a cut with the chain running at full speed and the spike bar in contact with the wood.

WARNING!

Never use the saw with one hand. You cannot control reactive forces (see pages 9 to 11) and may lose control of the saw.

8

WARNING!

Do not operate your chain saw in semi-throttle position. Cutting in this position does not permit the operator proper control of the saw or chain speed.

WARNING!

Never come too close to a rotating chain with your hands or body.

WARNING!

Do not cut any material other than wood or wooden objects.

Use your chain saw for cutting only. It is not designed for prying or shoveling away limbs, roots or other objects.

When sawing, make sure that the saw chain does not touch any foreign materials such as rocks, nails and the like (fig. 8). Such objects may be flung off, damage the saw chain or cause the saw to kick back.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Owner’s Safety Manual Contents Makita DCS 330 THCase one of the parts listed should not be included SymbolsEngine stop switch Delivery inventorySafety precautions for chain saw operators Additional safety precautionsPhysical Condition General Safety PrecautionsOperator Proper clothing SawUse of the saw Transporting the chain sawChain saw operating instructions FeetFueling Fueling instructionsCutting instructions Important adjustmentsWorking conditions Kickback Reactive forces during the cut, including kickbackSaw chain cutter sharpness To avoid kickbackSpeed of contact at which the cutter contacts the object Depth gaugesCutting techniques PushbackTo avoid pushback To avoid pull-inFelling instructions = cutting down areaPlunge-Cut Method Sectioning MethodLimbing BuckingMaintenance and Repair Maintaining and storing the sawDenomination of components Technical data DCS 330 TH Approved bar and chain combinationsStop Mounting the guide bar and saw chainTightening the saw chain Chain brake Checking the chain tensionEngaging the chain brake braking Releasing the chain brakeFuel Chain oilFuel mixture Correct mixture ratioClean screw cap and tank after refuelling Waste oilRefuelling Important note on bio-degradable chain oilsAdjusting the chain lubrication Checking the chain lubricationStarting the engine Cold startWarm start Stopping the engineAdjusting the carburetor Checking the chain brakeImportant information Set idle speed stepMin Sharpening the saw chain Stop65 mm 025 Files and how to work with them Cleaning the brake band and sprocket interior Cleaning the guide bar, lubricating the sprocket noseReplacing the suction head Cleaning the air filter StopReplacing the saw chain Replacing the spark plug Replacing the starter cableElectrode gap Checking the ignition sparkReplacing the return spring Cleaning the muffler / spark arrester screenCleaning the cylinder space Maintenance and repair Instructions for daily and periodic maintenanceService, spare parts and guarantee Troubleshooting GuaranteeSpare parts Malfunction System Observation CauseExtract from the spare parts list DCS 330 THFor your notes Sommaire Ce produit est en conformité avecSi un des composants indiqués ici ne devait pas être SymbolesEtendue de la fourniture Mesures de sé curité supplé mentaires Condition physique Mesures gé né rales de sé curité’utilisateur Quels vê tements porter? La tronç onneuseUtilisation de la tronç onneuse Transport de la tronç onneuseDé marrage Ravitaillement en carburantInstructions de ravitaillement Instructions de coupe Ré glages importantsConditions de travail Choc de recul Kickback Les limiteurs de profondeurs Affû tage des plaquettes de coupe de la chaînePour é viter le choc de recul Techniques de coupe Le reculPour é viter le recul Pour é viter la tractionInstructions d’abattage = zone d’abattageMé thode de sectionnement Mé thode de coupe en plongé eEbranchage Dé bitageEntretien et ré paration Entretien et stockage de la tronç onneuseDé signation des piè ces Levier de gaz Bouton de blocage pour mi-gazCaracté ristiques techniques DCS 330 TH Combinaisons autorisé es de guides et de chaînesMise EN Route Montage du rail-guide et de la chaîne de sciageTendre la chaîne de sciage RemarqueFrein de chaîne Contrô le de la tension de la chaîneEnclencher le frein de chaîne bloquer Libé rer le frein à mainCarburants Huile de chaîne de sciageMé lange carburant Ré alisation du rapport correct du mé langeRemarque importante pour les huiles de chaîne De sciage bio Huile Usagé eRemplissage des ré servoirs Ré glage du graissage de la chaîne Vé rifier le graissage de la chaîneEffectuer que si le moteur est arrê té ! Stop RemarqueDé marrer le moteur Dé marrage à froidDé marrage à chaud Arrê ter le moteurVé rifier le frein de chaîne Ré glage du carburateurInformation importante Ré glage du ralenti marche à vide pointAffû tage de la chaîne De sciage 65 mmLime et guidage de la lime Nettoyer le guide-chaîne Regraisser l’é toile de dé viation Remplacement de la cré pine d’aspiration Nouvelle chaîne de sciageNettoyage du filtre d’air Stop Ne pas nettoyer le filtre à air à l’essenceRemplacement de bougie Remplacement du cordon de lancementEcartement des é lectrodes Vé rification de l’é tincelle d’allumageRemplacement du ressort de rappel Nettoyer le silencieux / du pare-é tincellesNettoyer l’inté rieur du cylindre Risque de blesssure! Un ressort cassé peut sauterMaintenance et ré parations Service d’atelier, piè ces de rechange et garantieIndications de maintenance et d’entretien pé riodiques Piè ces de rechange GarantieRecherche de pannes Panne Systè me Observation OrigineExtrait de la liste des piè ces de rechange Notas Makita U.S.A., Inc Makita Canada Inc USA

DCS 330 TH specifications

The Makita DCS 330 TH is a powerful and versatile chainsaw designed for professional users who demand high performance and reliability in their tools. This model is particularly favored for its exceptional cutting capabilities, making it an ideal choice for both forestry applications and general landscaping tasks.

One of the standout features of the Makita DCS 330 TH is its robust 32.2 cc 2-stroke engine, which delivers impressive power for cutting through various types of wood. With an engine speed of up to 12,000 RPM, this chainsaw can tackle thick branches and logs with ease, allowing the user to complete their tasks efficiently. The combination of power and lightweight design ensures that users can handle the saw comfortably for extended periods without excessive fatigue.

The chainsaw is equipped with a 12-inch guide bar, which enables precise cutting while maintaining a manageable size for various applications. This length strikes an optimal balance between maneuverability and cutting depth, making the DCS 330 TH an excellent choice for both pruning and felling small to medium-sized trees.

The Makita DCS 330 TH also incorporates advanced technologies that enhance its performance and user experience. One of these technologies is the automatic oil pump, which ensures that the chain is adequately lubricated during operation. This feature not only prolongs the life of the chain and bar but also enhances cutting efficiency and safety.

User comfort is further prioritized through the inclusion of an anti-vibration system that minimizes the impact of vibration during operation. This system significantly reduces user fatigue and allows for more precise control, making it easier to perform detailed cutting tasks.

Safety features are also a prominent aspect of the Makita DCS 330 TH. The chainsaw is designed with a chain brake system that quickly halts the chain in case of kickback, providing an additional layer of protection for the operator. Additionally, the tool's throttle lock ensures that the saw remains stable during operation, preventing accidental starts.

In summary, the Makita DCS 330 TH is a highly capable chainsaw that combines power, comfort, and safety features into one reliable package. Its lightweight design, advanced technologies, and user-friendly characteristics make it an excellent choice for anyone looking to invest in a quality chainsaw for demanding applications.
Top Page Image Contents