Makita DCS 330 TH instruction manual Tightening the saw chain

Page 19

Lift the chain (11) over the clutch drum and onto the sprocket (12). Using your right hand, guide the chain into the top guide groove on the guide bar. Note that the cutting edges along the top of the chain must point in the direction of the arrow!

12 11

E

11 13

Lead the chain (11) around the sprocket nose (13) of the guide bar.

NOTE:

The chain should be easy to pull in the direction of the arrow. The clutch drum (E/12) should turn with the chain (the sprocket engages the chain).

 

 

F

First push the sprocket guard (3) into the mounting (4) and then

 

 

over the mounting bolt (14).

 

 

NOTE:

 

3

If the chain brake on the dismounted chain guard is inadver-

 

 

tently actuated, it will not be possible to push the sprocket

 

 

guard all the way over the mounting bolt. You will first have to

4

14

release the chain brake (Fig. B).

2

 

 

Tighten the mounting nut (2) hand-tight.

 

 

 

 

G

Tightening the saw chain

Turn the chain tightener (C/6) to the right (clockwise) until the chain engages the guide groove of the bottom side of the bar (see circle).

Slightly lift the end of the guide bar and turn the chain adjusting screw (C/6) to the right (clockwise) until the chain rests against the bottom side of the guide bar.

While still holding up the guide bar, tighten the retaining nut (2) with the universal wrench.

2

H

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Owner’s Safety Manual Makita DCS 330 TH ContentsDelivery inventory Case one of the parts listed should not be includedSymbols Engine stop switchAdditional safety precautions Safety precautions for chain saw operatorsOperator General Safety PrecautionsPhysical Condition Transporting the chain saw Proper clothingSaw Use of the sawFueling instructions Chain saw operating instructionsFeet FuelingWorking conditions Important adjustmentsCutting instructions Reactive forces during the cut, including kickback KickbackDepth gauges Saw chain cutter sharpnessTo avoid kickback Speed of contact at which the cutter contacts the objectTo avoid pull-in Cutting techniquesPushback To avoid pushback= cutting down area Felling instructionsSectioning Method Plunge-Cut MethodBucking LimbingMaintaining and storing the saw Maintenance and RepairDenomination of components Approved bar and chain combinations Technical data DCS 330 THMounting the guide bar and saw chain StopTightening the saw chain Releasing the chain brake Chain brakeChecking the chain tension Engaging the chain brake brakingCorrect mixture ratio FuelChain oil Fuel mixtureImportant note on bio-degradable chain oils Clean screw cap and tank after refuellingWaste oil RefuellingChecking the chain lubrication Adjusting the chain lubricationStopping the engine Starting the engineCold start Warm startSet idle speed step Adjusting the carburetorChecking the chain brake Important information65 mm 025 Sharpening the saw chain StopMin Files and how to work with them Cleaning the guide bar, lubricating the sprocket nose Cleaning the brake band and sprocket interiorReplacing the saw chain Cleaning the air filter StopReplacing the suction head Checking the ignition spark Replacing the spark plugReplacing the starter cable Electrode gapCleaning the cylinder space Cleaning the muffler / spark arrester screenReplacing the return spring Service, spare parts and guarantee Instructions for daily and periodic maintenanceMaintenance and repair Malfunction System Observation Cause TroubleshootingGuarantee Spare partsDCS 330 TH Extract from the spare parts listFor your notes Ce produit est en conformité avec SommaireEtendue de la fourniture SymbolesSi un des composants indiqués ici ne devait pas être Mesures de sé curité supplé mentaires ’utilisateur Mesures gé né rales de sé curitéCondition physique Transport de la tronç onneuse Quels vê tements porter?La tronç onneuse Utilisation de la tronç onneuseInstructions de ravitaillement Ravitaillement en carburantDé marrage Conditions de travail Ré glages importantsInstructions de coupe Choc de recul Kickback Pour é viter le choc de recul Affû tage des plaquettes de coupe de la chaîneLes limiteurs de profondeurs Pour é viter la traction Techniques de coupeLe recul Pour é viter le recul= zone d’abattage Instructions d’abattageMé thode de coupe en plongé e Mé thode de sectionnementDé bitage EbranchageEntretien et stockage de la tronç onneuse Entretien et ré parationLevier de gaz Bouton de blocage pour mi-gaz Dé signation des piè cesCombinaisons autorisé es de guides et de chaînes Caracté ristiques techniques DCS 330 THMontage du rail-guide et de la chaîne de sciage Mise EN RouteRemarque Tendre la chaîne de sciageLibé rer le frein à main Frein de chaîneContrô le de la tension de la chaîne Enclencher le frein de chaîne bloquerRé alisation du rapport correct du mé lange CarburantsHuile de chaîne de sciage Mé lange carburantRemplissage des ré servoirs Huile Usagé eRemarque importante pour les huiles de chaîne De sciage bio Remarque Ré glage du graissage de la chaîneVé rifier le graissage de la chaîne Effectuer que si le moteur est arrê té ! StopArrê ter le moteur Dé marrer le moteurDé marrage à froid Dé marrage à chaudRé glage du ralenti marche à vide point Vé rifier le frein de chaîneRé glage du carburateur Information importante65 mm Affû tage de la chaîne De sciageLime et guidage de la lime Nettoyer le guide-chaîne Regraisser l’é toile de dé viation Ne pas nettoyer le filtre à air à l’essence Remplacement de la cré pine d’aspirationNouvelle chaîne de sciage Nettoyage du filtre d’air StopVé rification de l’é tincelle d’allumage Remplacement de bougieRemplacement du cordon de lancement Ecartement des é lectrodesRisque de blesssure! Un ressort cassé peut sauter Remplacement du ressort de rappelNettoyer le silencieux / du pare-é tincelles Nettoyer l’inté rieur du cylindreIndications de maintenance et d’entretien pé riodiques Service d’atelier, piè ces de rechange et garantieMaintenance et ré parations Panne Systè me Observation Origine Piè ces de rechangeGarantie Recherche de pannesExtrait de la liste des piè ces de rechange Notas USA Makita U.S.A., Inc Makita Canada Inc

DCS 330 TH specifications

The Makita DCS 330 TH is a powerful and versatile chainsaw designed for professional users who demand high performance and reliability in their tools. This model is particularly favored for its exceptional cutting capabilities, making it an ideal choice for both forestry applications and general landscaping tasks.

One of the standout features of the Makita DCS 330 TH is its robust 32.2 cc 2-stroke engine, which delivers impressive power for cutting through various types of wood. With an engine speed of up to 12,000 RPM, this chainsaw can tackle thick branches and logs with ease, allowing the user to complete their tasks efficiently. The combination of power and lightweight design ensures that users can handle the saw comfortably for extended periods without excessive fatigue.

The chainsaw is equipped with a 12-inch guide bar, which enables precise cutting while maintaining a manageable size for various applications. This length strikes an optimal balance between maneuverability and cutting depth, making the DCS 330 TH an excellent choice for both pruning and felling small to medium-sized trees.

The Makita DCS 330 TH also incorporates advanced technologies that enhance its performance and user experience. One of these technologies is the automatic oil pump, which ensures that the chain is adequately lubricated during operation. This feature not only prolongs the life of the chain and bar but also enhances cutting efficiency and safety.

User comfort is further prioritized through the inclusion of an anti-vibration system that minimizes the impact of vibration during operation. This system significantly reduces user fatigue and allows for more precise control, making it easier to perform detailed cutting tasks.

Safety features are also a prominent aspect of the Makita DCS 330 TH. The chainsaw is designed with a chain brake system that quickly halts the chain in case of kickback, providing an additional layer of protection for the operator. Additionally, the tool's throttle lock ensures that the saw remains stable during operation, preventing accidental starts.

In summary, the Makita DCS 330 TH is a highly capable chainsaw that combines power, comfort, and safety features into one reliable package. Its lightweight design, advanced technologies, and user-friendly characteristics make it an excellent choice for anyone looking to invest in a quality chainsaw for demanding applications.
Top Page Image Contents