Makita DCS 330 TH Checking the chain brake, Adjusting the carburetor, Important information

Page 25

Checking the chain brake

Do not work with the chain saw without first checking the chain brake!

Start the engine as described (make sure you have a good footing, and place the chain saw on the ground in such a way that the guide bar is free of contact).

Grasp the tubular handle firmly with one hand and hold the rear handle with the other.

With the engine running at moderate speed, press the hand guard (L/6) in the direction of the arrow with the back of your hand until the chain brake engages. The chain should stop immediately.

Immediately release the throttle and release the chain brake.

IMPORTANT:

If the chain does not stop immediately in this test, do not under any circumstances proceed with work. Contact a MAKITA service center for repair.

6

C

Adjusting the carburetor

Important information:

The carburetor of this tool is fitted with limiter caps which restrict the range of adjustment and prevents over-rich mixture settings. This ensures providing good engine power and efficient fuel consumption.

Before installing the limiter caps, the manufacturer performs the „Basic Adjustment” procedure.

Optimum perfornance can only be achieved if the carbure- tor is adjusted correctly. For this work, which should be carried out by an expert, the engine must be warmed up and the air filter clean.

It is urgently recommended to use a revolution indicator (8) (accessorie, not delivered with the chain saw) in order to achieve a correct adjustment of the carburetor. Adjust the carburetor using a 0.16" (4 mm) screwdriver.

The screwdriver shown (7) (accessorie, not delivered with the chain saw) has a molded-on lug to assist in adjustment.

Before adjusting the carburetor the engine must be warmed up for a period of 3-5 min.

7 8

HL

9

IDLE

10

11

Adjustment instructions (step 1) STOP

For adjusting the carburetor correctly the following steps must be carried out:

1. Check adjustment

 

STOP

 

2.Start engine

3.Set idle speed

4.Adjust speed

5.Check idling speed

6.Check acceleration

7.Check max. speed or output

8.Repeat adjustment procedure starting with step 3, until idling speed, max. speed and acceleration are reached with the adjustment made.

Before initial operation make sure that the adjusting screws (9 and 10) have not been set in all the way. Limiter caps do not protect the engine from leaning.

Turn the two adjusting screws (9 and 10) counter-clock- wise as far as they will go.

Start the engine and let it warm up (step 2).

Set idle speed (step 3)

If the chain turns when the engine is idling, unscrew the throttle-valve stop screw (11) until the chain stops. If the engine runs unevenly, screw the screw (11) back in.

Idling speed should be 2,800 rpm.

D

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Owner’s Safety Manual Makita DCS 330 TH ContentsSymbols Case one of the parts listed should not be includedEngine stop switch Delivery inventoryAdditional safety precautions Safety precautions for chain saw operatorsOperator General Safety PrecautionsPhysical Condition Saw Proper clothingUse of the saw Transporting the chain sawFeet Chain saw operating instructionsFueling Fueling instructionsWorking conditions Important adjustmentsCutting instructions Reactive forces during the cut, including kickback KickbackTo avoid kickback Saw chain cutter sharpnessSpeed of contact at which the cutter contacts the object Depth gaugesPushback Cutting techniquesTo avoid pushback To avoid pull-in= cutting down area Felling instructionsSectioning Method Plunge-Cut MethodBucking LimbingMaintaining and storing the saw Maintenance and RepairDenomination of components Approved bar and chain combinations Technical data DCS 330 THMounting the guide bar and saw chain StopTightening the saw chain Checking the chain tension Chain brakeEngaging the chain brake braking Releasing the chain brakeChain oil FuelFuel mixture Correct mixture ratioWaste oil Clean screw cap and tank after refuellingRefuelling Important note on bio-degradable chain oilsChecking the chain lubrication Adjusting the chain lubricationCold start Starting the engineWarm start Stopping the engineChecking the chain brake Adjusting the carburetorImportant information Set idle speed step65 mm 025 Sharpening the saw chain StopMin Files and how to work with them Cleaning the guide bar, lubricating the sprocket nose Cleaning the brake band and sprocket interiorReplacing the saw chain Cleaning the air filter StopReplacing the suction head Replacing the starter cable Replacing the spark plugElectrode gap Checking the ignition sparkCleaning the cylinder space Cleaning the muffler / spark arrester screenReplacing the return spring Service, spare parts and guarantee Instructions for daily and periodic maintenanceMaintenance and repair Guarantee TroubleshootingSpare parts Malfunction System Observation CauseDCS 330 TH Extract from the spare parts listFor your notes Ce produit est en conformité avec SommaireEtendue de la fourniture SymbolesSi un des composants indiqués ici ne devait pas être Mesures de sé curité supplé mentaires ’utilisateur Mesures gé né rales de sé curitéCondition physique La tronç onneuse Quels vê tements porter?Utilisation de la tronç onneuse Transport de la tronç onneuseInstructions de ravitaillement Ravitaillement en carburantDé marrage Conditions de travail Ré glages importantsInstructions de coupe Choc de recul Kickback Pour é viter le choc de recul Affû tage des plaquettes de coupe de la chaîneLes limiteurs de profondeurs Le recul Techniques de coupePour é viter le recul Pour é viter la traction= zone d’abattage Instructions d’abattageMé thode de coupe en plongé e Mé thode de sectionnementDé bitage EbranchageEntretien et stockage de la tronç onneuse Entretien et ré parationLevier de gaz Bouton de blocage pour mi-gaz Dé signation des piè cesCombinaisons autorisé es de guides et de chaînes Caracté ristiques techniques DCS 330 THMontage du rail-guide et de la chaîne de sciage Mise EN RouteRemarque Tendre la chaîne de sciageContrô le de la tension de la chaîne Frein de chaîneEnclencher le frein de chaîne bloquer Libé rer le frein à mainHuile de chaîne de sciage CarburantsMé lange carburant Ré alisation du rapport correct du mé langeRemplissage des ré servoirs Huile Usagé eRemarque importante pour les huiles de chaîne De sciage bio Vé rifier le graissage de la chaîne Ré glage du graissage de la chaîneEffectuer que si le moteur est arrê té ! Stop RemarqueDé marrage à froid Dé marrer le moteurDé marrage à chaud Arrê ter le moteurRé glage du carburateur Vé rifier le frein de chaîneInformation importante Ré glage du ralenti marche à vide point65 mm Affû tage de la chaîne De sciageLime et guidage de la lime Nettoyer le guide-chaîne Regraisser l’é toile de dé viation Nouvelle chaîne de sciage Remplacement de la cré pine d’aspirationNettoyage du filtre d’air Stop Ne pas nettoyer le filtre à air à l’essenceRemplacement du cordon de lancement Remplacement de bougieEcartement des é lectrodes Vé rification de l’é tincelle d’allumageNettoyer le silencieux / du pare-é tincelles Remplacement du ressort de rappelNettoyer l’inté rieur du cylindre Risque de blesssure! Un ressort cassé peut sauterIndications de maintenance et d’entretien pé riodiques Service d’atelier, piè ces de rechange et garantieMaintenance et ré parations Garantie Piè ces de rechangeRecherche de pannes Panne Systè me Observation OrigineExtrait de la liste des piè ces de rechange Notas USA Makita U.S.A., Inc Makita Canada Inc

DCS 330 TH specifications

The Makita DCS 330 TH is a powerful and versatile chainsaw designed for professional users who demand high performance and reliability in their tools. This model is particularly favored for its exceptional cutting capabilities, making it an ideal choice for both forestry applications and general landscaping tasks.

One of the standout features of the Makita DCS 330 TH is its robust 32.2 cc 2-stroke engine, which delivers impressive power for cutting through various types of wood. With an engine speed of up to 12,000 RPM, this chainsaw can tackle thick branches and logs with ease, allowing the user to complete their tasks efficiently. The combination of power and lightweight design ensures that users can handle the saw comfortably for extended periods without excessive fatigue.

The chainsaw is equipped with a 12-inch guide bar, which enables precise cutting while maintaining a manageable size for various applications. This length strikes an optimal balance between maneuverability and cutting depth, making the DCS 330 TH an excellent choice for both pruning and felling small to medium-sized trees.

The Makita DCS 330 TH also incorporates advanced technologies that enhance its performance and user experience. One of these technologies is the automatic oil pump, which ensures that the chain is adequately lubricated during operation. This feature not only prolongs the life of the chain and bar but also enhances cutting efficiency and safety.

User comfort is further prioritized through the inclusion of an anti-vibration system that minimizes the impact of vibration during operation. This system significantly reduces user fatigue and allows for more precise control, making it easier to perform detailed cutting tasks.

Safety features are also a prominent aspect of the Makita DCS 330 TH. The chainsaw is designed with a chain brake system that quickly halts the chain in case of kickback, providing an additional layer of protection for the operator. Additionally, the tool's throttle lock ensures that the saw remains stable during operation, preventing accidental starts.

In summary, the Makita DCS 330 TH is a highly capable chainsaw that combines power, comfort, and safety features into one reliable package. Its lightweight design, advanced technologies, and user-friendly characteristics make it an excellent choice for anyone looking to invest in a quality chainsaw for demanding applications.
Top Page Image Contents