Makita DCS 330 TH instruction manual Stop, Mounting the guide bar and saw chain

Page 18

PUTTING INTO OPERATION

CAUTION:

STOP

A

Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see "Replacing the spark plug"). Always wear pro- tective gloves!

CAUTION:

Do not start the saw until it has been completely assem- bled and inspected!

4

B

1 2

3

Mounting the guide bar and saw chain

Use the universal wrench delivered with the chain saw for the following work.

Put the chain saw on a stable surface and carry out the following steps for mounting the guide bar and chain:

Disengage the chain brake by pulling the hand guard (1) in the direction of the arrow.

Unscrew retaining nut (2).

Spread the sprocket guard (3) slightly, push it out of the mounting (4) and remove it.

Remove the transport cover (5).

Turn the chain tensioning screw (6) to the left (counter-clock- wise) until the lug (7) is below the guide pin (8).

5

C

8

7

6

Position the guide bar (9). Make sure that the pin (10) of the chain tightener is in the hole on the guide bar.

9

D

10

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Owner’s Safety Manual Contents Makita DCS 330 THEngine stop switch Case one of the parts listed should not be includedSymbols Delivery inventorySafety precautions for chain saw operators Additional safety precautionsGeneral Safety Precautions OperatorPhysical Condition Use of the saw Proper clothingSaw Transporting the chain sawFueling Chain saw operating instructionsFeet Fueling instructionsImportant adjustments Working conditionsCutting instructions Kickback Reactive forces during the cut, including kickbackSpeed of contact at which the cutter contacts the object Saw chain cutter sharpnessTo avoid kickback Depth gaugesTo avoid pushback Cutting techniquesPushback To avoid pull-inFelling instructions = cutting down areaPlunge-Cut Method Sectioning MethodLimbing BuckingMaintenance and Repair Maintaining and storing the sawDenomination of components Technical data DCS 330 TH Approved bar and chain combinationsStop Mounting the guide bar and saw chainTightening the saw chain Engaging the chain brake braking Chain brakeChecking the chain tension Releasing the chain brakeFuel mixture FuelChain oil Correct mixture ratioRefuelling Clean screw cap and tank after refuellingWaste oil Important note on bio-degradable chain oilsAdjusting the chain lubrication Checking the chain lubricationWarm start Starting the engineCold start Stopping the engineImportant information Adjusting the carburetorChecking the chain brake Set idle speed stepSharpening the saw chain Stop 65 mm 025Min Files and how to work with them Cleaning the brake band and sprocket interior Cleaning the guide bar, lubricating the sprocket noseCleaning the air filter Stop Replacing the saw chainReplacing the suction head Electrode gap Replacing the spark plugReplacing the starter cable Checking the ignition sparkCleaning the muffler / spark arrester screen Cleaning the cylinder spaceReplacing the return spring Instructions for daily and periodic maintenance Service, spare parts and guaranteeMaintenance and repair Spare parts TroubleshootingGuarantee Malfunction System Observation CauseExtract from the spare parts list DCS 330 THFor your notes Sommaire Ce produit est en conformité avecSymboles Etendue de la fournitureSi un des composants indiqués ici ne devait pas être Mesures de sé curité supplé mentaires Mesures gé né rales de sé curité ’utilisateurCondition physique Utilisation de la tronç onneuse Quels vê tements porter?La tronç onneuse Transport de la tronç onneuseRavitaillement en carburant Instructions de ravitaillementDé marrage Ré glages importants Conditions de travailInstructions de coupe Choc de recul Kickback Affû tage des plaquettes de coupe de la chaîne Pour é viter le choc de reculLes limiteurs de profondeurs Pour é viter le recul Techniques de coupeLe recul Pour é viter la tractionInstructions d’abattage = zone d’abattageMé thode de sectionnement Mé thode de coupe en plongé eEbranchage Dé bitageEntretien et ré paration Entretien et stockage de la tronç onneuseDé signation des piè ces Levier de gaz Bouton de blocage pour mi-gazCaracté ristiques techniques DCS 330 TH Combinaisons autorisé es de guides et de chaînesMise EN Route Montage du rail-guide et de la chaîne de sciageTendre la chaîne de sciage RemarqueEnclencher le frein de chaîne bloquer Frein de chaîneContrô le de la tension de la chaîne Libé rer le frein à mainMé lange carburant CarburantsHuile de chaîne de sciage Ré alisation du rapport correct du mé langeHuile Usagé e Remplissage des ré servoirsRemarque importante pour les huiles de chaîne De sciage bio Effectuer que si le moteur est arrê té ! Stop Ré glage du graissage de la chaîneVé rifier le graissage de la chaîne RemarqueDé marrage à chaud Dé marrer le moteurDé marrage à froid Arrê ter le moteurInformation importante Vé rifier le frein de chaîneRé glage du carburateur Ré glage du ralenti marche à vide pointAffû tage de la chaîne De sciage 65 mmLime et guidage de la lime Nettoyer le guide-chaîne Regraisser l’é toile de dé viation Nettoyage du filtre d’air Stop Remplacement de la cré pine d’aspirationNouvelle chaîne de sciage Ne pas nettoyer le filtre à air à l’essenceEcartement des é lectrodes Remplacement de bougieRemplacement du cordon de lancement Vé rification de l’é tincelle d’allumageNettoyer l’inté rieur du cylindre Remplacement du ressort de rappelNettoyer le silencieux / du pare-é tincelles Risque de blesssure! Un ressort cassé peut sauterService d’atelier, piè ces de rechange et garantie Indications de maintenance et d’entretien pé riodiquesMaintenance et ré parations Recherche de pannes Piè ces de rechangeGarantie Panne Systè me Observation OrigineExtrait de la liste des piè ces de rechange Notas Makita U.S.A., Inc Makita Canada Inc USA

DCS 330 TH specifications

The Makita DCS 330 TH is a powerful and versatile chainsaw designed for professional users who demand high performance and reliability in their tools. This model is particularly favored for its exceptional cutting capabilities, making it an ideal choice for both forestry applications and general landscaping tasks.

One of the standout features of the Makita DCS 330 TH is its robust 32.2 cc 2-stroke engine, which delivers impressive power for cutting through various types of wood. With an engine speed of up to 12,000 RPM, this chainsaw can tackle thick branches and logs with ease, allowing the user to complete their tasks efficiently. The combination of power and lightweight design ensures that users can handle the saw comfortably for extended periods without excessive fatigue.

The chainsaw is equipped with a 12-inch guide bar, which enables precise cutting while maintaining a manageable size for various applications. This length strikes an optimal balance between maneuverability and cutting depth, making the DCS 330 TH an excellent choice for both pruning and felling small to medium-sized trees.

The Makita DCS 330 TH also incorporates advanced technologies that enhance its performance and user experience. One of these technologies is the automatic oil pump, which ensures that the chain is adequately lubricated during operation. This feature not only prolongs the life of the chain and bar but also enhances cutting efficiency and safety.

User comfort is further prioritized through the inclusion of an anti-vibration system that minimizes the impact of vibration during operation. This system significantly reduces user fatigue and allows for more precise control, making it easier to perform detailed cutting tasks.

Safety features are also a prominent aspect of the Makita DCS 330 TH. The chainsaw is designed with a chain brake system that quickly halts the chain in case of kickback, providing an additional layer of protection for the operator. Additionally, the tool's throttle lock ensures that the saw remains stable during operation, preventing accidental starts.

In summary, the Makita DCS 330 TH is a highly capable chainsaw that combines power, comfort, and safety features into one reliable package. Its lightweight design, advanced technologies, and user-friendly characteristics make it an excellent choice for anyone looking to invest in a quality chainsaw for demanding applications.
Top Page Image Contents