Makita DCS 330 TH instruction manual General Safety Precautions, Operator, Physical Condition

Page 5

General Safety Precautions

The use of any chain saw may be hazardous. At full throttle chain speed can reach 45 mph (20 m/s). It is important that you read; fully understand and observe the following safety precautions and warnings. Read the owner’s manual and the safety instructions periodically.

WARNING !

Reactive forces, including kickback, can be dan- gerous. Careless or improper use of any chain saw may cause serious or fatal injury.

XXX.YYY.ZZZ

XXX.YYY.ZZZ

Always use two hands when operating the chain saw!

Reduced Kickback Bar and Chain combination that has been evaluated with the power head to achieve kickback protection (according to ANSI and CSA standards).

Have your MAKITA dealer show you how to operate your chain saw. Observe all applicable local safety regulations, standards and ordinances.

*The Computed Kickback Angle is a calculated value from energies measured on a test bench. It is not the angle of the guide bar moved upward in case of a

KICKBACK.

1

The operator

Physical Condition

You must be in good physical condition and mental health and not under the influence of any substance (drugs, alcohol), which might impair vision, dexterity or judgment.

WARNING!

Minors should never be allowed to use a chain saw.

Bystanders, especially children and animals should not be allowed in the area where a chain saw is in use (fig. 1).

Never let the saw run unattended.

Store it in a locked place away from children. Fill the fuel tank to 7/8 th full (see storing the saw). Do not lend your chain saw without this owner’s manual. Be sure that anyone using your saw un- derstands the information given.

Proper use of a chain saw involves

1.the operator

2.the saw

3.the use of the saw.

max. CKA 21O Maximum Computed Kickback Angle

(CKA)* without using the chain brake when using the recommended bar and chain

combinations (In this example the CKA is 21°).

Contact of the guide bar tip with any object should be avoided! Tip contact may cause the guide bar to move suddenly upward and backward, which may cause serious injury!

2

WARNING !

Prolonged use of chain saws exposing the operator to vibrations may produce Whitefinger disease (Raynaud’s phenomenon). This phenomenon reduces the hand’s ability to feel and regulate temperature, produces numbness and burning sensations and may cause nerve and circulation damage and tissue necrosis.

All MAKITA saws are therefore provided with an antivibration system which is essential for those using chain saws on a regular or sustained basis. Antivibration systems do not guarantee that you will not sustain Whitefinger disesase, however, they reduce this danger considerably. Nevertheless, continual and regular users should observe their hands and fingers and in case of any abnormal symptoms, seek medical advice immediately.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Owner’s Safety Manual Makita DCS 330 TH ContentsSymbols Case one of the parts listed should not be includedEngine stop switch Delivery inventoryAdditional safety precautions Safety precautions for chain saw operatorsPhysical Condition General Safety PrecautionsOperator Saw Proper clothingUse of the saw Transporting the chain sawFeet Chain saw operating instructionsFueling Fueling instructionsCutting instructions Important adjustmentsWorking conditions Reactive forces during the cut, including kickback KickbackTo avoid kickback Saw chain cutter sharpnessSpeed of contact at which the cutter contacts the object Depth gaugesPushback Cutting techniquesTo avoid pushback To avoid pull-in= cutting down area Felling instructionsSectioning Method Plunge-Cut MethodBucking LimbingMaintaining and storing the saw Maintenance and RepairDenomination of components Approved bar and chain combinations Technical data DCS 330 THMounting the guide bar and saw chain StopTightening the saw chain Checking the chain tension Chain brakeEngaging the chain brake braking Releasing the chain brakeChain oil FuelFuel mixture Correct mixture ratioWaste oil Clean screw cap and tank after refuellingRefuelling Important note on bio-degradable chain oilsChecking the chain lubrication Adjusting the chain lubricationCold start Starting the engineWarm start Stopping the engineChecking the chain brake Adjusting the carburetorImportant information Set idle speed stepMin Sharpening the saw chain Stop65 mm 025 Files and how to work with them Cleaning the guide bar, lubricating the sprocket nose Cleaning the brake band and sprocket interiorReplacing the suction head Cleaning the air filter StopReplacing the saw chain Replacing the starter cable Replacing the spark plugElectrode gap Checking the ignition sparkReplacing the return spring Cleaning the muffler / spark arrester screenCleaning the cylinder space Maintenance and repair Instructions for daily and periodic maintenanceService, spare parts and guarantee Guarantee TroubleshootingSpare parts Malfunction System Observation CauseDCS 330 TH Extract from the spare parts listFor your notes Ce produit est en conformité avec SommaireSi un des composants indiqués ici ne devait pas être SymbolesEtendue de la fourniture Mesures de sé curité supplé mentaires Condition physique Mesures gé né rales de sé curité’utilisateur La tronç onneuse Quels vê tements porter?Utilisation de la tronç onneuse Transport de la tronç onneuseDé marrage Ravitaillement en carburantInstructions de ravitaillement Instructions de coupe Ré glages importantsConditions de travail Choc de recul Kickback Les limiteurs de profondeurs Affû tage des plaquettes de coupe de la chaînePour é viter le choc de recul Le recul Techniques de coupePour é viter le recul Pour é viter la traction= zone d’abattage Instructions d’abattageMé thode de coupe en plongé e Mé thode de sectionnementDé bitage EbranchageEntretien et stockage de la tronç onneuse Entretien et ré parationLevier de gaz Bouton de blocage pour mi-gaz Dé signation des piè cesCombinaisons autorisé es de guides et de chaînes Caracté ristiques techniques DCS 330 THMontage du rail-guide et de la chaîne de sciage Mise EN RouteRemarque Tendre la chaîne de sciageContrô le de la tension de la chaîne Frein de chaîneEnclencher le frein de chaîne bloquer Libé rer le frein à mainHuile de chaîne de sciage CarburantsMé lange carburant Ré alisation du rapport correct du mé langeRemarque importante pour les huiles de chaîne De sciage bio Huile Usagé eRemplissage des ré servoirs Vé rifier le graissage de la chaîne Ré glage du graissage de la chaîneEffectuer que si le moteur est arrê té ! Stop RemarqueDé marrage à froid Dé marrer le moteurDé marrage à chaud Arrê ter le moteurRé glage du carburateur Vé rifier le frein de chaîneInformation importante Ré glage du ralenti marche à vide point65 mm Affû tage de la chaîne De sciageLime et guidage de la lime Nettoyer le guide-chaîne Regraisser l’é toile de dé viation Nouvelle chaîne de sciage Remplacement de la cré pine d’aspirationNettoyage du filtre d’air Stop Ne pas nettoyer le filtre à air à l’essenceRemplacement du cordon de lancement Remplacement de bougieEcartement des é lectrodes Vé rification de l’é tincelle d’allumageNettoyer le silencieux / du pare-é tincelles Remplacement du ressort de rappelNettoyer l’inté rieur du cylindre Risque de blesssure! Un ressort cassé peut sauterMaintenance et ré parations Service d’atelier, piè ces de rechange et garantieIndications de maintenance et d’entretien pé riodiques Garantie Piè ces de rechangeRecherche de pannes Panne Systè me Observation OrigineExtrait de la liste des piè ces de rechange Notas USA Makita U.S.A., Inc Makita Canada Inc

DCS 330 TH specifications

The Makita DCS 330 TH is a powerful and versatile chainsaw designed for professional users who demand high performance and reliability in their tools. This model is particularly favored for its exceptional cutting capabilities, making it an ideal choice for both forestry applications and general landscaping tasks.

One of the standout features of the Makita DCS 330 TH is its robust 32.2 cc 2-stroke engine, which delivers impressive power for cutting through various types of wood. With an engine speed of up to 12,000 RPM, this chainsaw can tackle thick branches and logs with ease, allowing the user to complete their tasks efficiently. The combination of power and lightweight design ensures that users can handle the saw comfortably for extended periods without excessive fatigue.

The chainsaw is equipped with a 12-inch guide bar, which enables precise cutting while maintaining a manageable size for various applications. This length strikes an optimal balance between maneuverability and cutting depth, making the DCS 330 TH an excellent choice for both pruning and felling small to medium-sized trees.

The Makita DCS 330 TH also incorporates advanced technologies that enhance its performance and user experience. One of these technologies is the automatic oil pump, which ensures that the chain is adequately lubricated during operation. This feature not only prolongs the life of the chain and bar but also enhances cutting efficiency and safety.

User comfort is further prioritized through the inclusion of an anti-vibration system that minimizes the impact of vibration during operation. This system significantly reduces user fatigue and allows for more precise control, making it easier to perform detailed cutting tasks.

Safety features are also a prominent aspect of the Makita DCS 330 TH. The chainsaw is designed with a chain brake system that quickly halts the chain in case of kickback, providing an additional layer of protection for the operator. Additionally, the tool's throttle lock ensures that the saw remains stable during operation, preventing accidental starts.

In summary, the Makita DCS 330 TH is a highly capable chainsaw that combines power, comfort, and safety features into one reliable package. Its lightweight design, advanced technologies, and user-friendly characteristics make it an excellent choice for anyone looking to invest in a quality chainsaw for demanding applications.
Top Page Image Contents