Troy-Bilt 68J-Horse, E686N-Horse Models 682J. E686N & E682L, Description QTY, 1186246, 725-0157

Page 45

MODELS 682J. E686N & E682L

Parts List

FORWARD INTERLOCK SYSTEM

See Page 46

REF

PART

 

 

No.

No.

DESCRIPTION

QTY.

 

 

 

 

1629-04017 Engine Wire Harness Assy–forward interlock system (Incl. one red and one black wire, plug con- nector, neutral switch and PVC tubing. Parts not available

separately

1

REF

PART

 

 

No.

No.

DESCRIPTION

QTY.

 

 

 

 

2

GW-9971

Lockwasher–external tooth, 7/16"

......1

3

1186246

Nut–hex, 7/16"-20

1

6

GW-9205

Clip–for plug connector

1

7

725-0157

Tie–plastic

2

8

GW-2551

Handlebar Wire Harness Assy–

 

 

 

(see page 46, Ref. No. 20)

1

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Operator’s Manual Table of Contents Safety Alert Symbol SafetyUse slower wheel, tine and engine speeds Keep children and pets awayTo Avoid Serious Injury Operating SymbolsIntroduction Tools/Materials Needed for AssemblyInspect Unit Attach HandlebarFront Tiller Move Tiller Off Shipping PlatformRemove the temporary screw J, Figure Check Gear Oil LevelsAttach Engine Throttle Lever and Cable Adjust Air Pressure in TiresAdd Motor Oil to Engine Oil Level HoleConnect the Wire Harness Receptacle Install Battery CablesTo Avoid Personal Injury or Property Damage Never bring a gas can near the positiveWheels/Tines/PTO Drive Lever PTO Attachments FeatureForward Interlock Levers EngineWheel Speed Lever Handlebar Height Adjustment LeverTines/PTO Clutch Lever Depth Regulator LeverKeyswitch Starter Engine Controls Engine Throttle LeverMove the engine Throttle lever to Stop position Pre-Start Checklist Following steps describe how to start and stop the engineBreak-In Operation Starting and Stopping the EngineMove engine throttle lever -2 away from Stop Move the throttle speed control to Fast setting when tillingOperating the Tiller Cold Weather OperationStopping the Engine and Tiller Moving the Tiller Forward and TillingStopping Reverse Motion Moving the Tiller in ReverseTo Stop the Engine Making TurnsHow to Check the Interlock System Testing the Forward Interlock Safety SystemLoading and Unloading the Tiller Transporting The Tiller Around Your PropertyLoading the Tiller Changing Speed BeltsUnloading the Tiller Changing Belt From LOW Range to High RangeChanging Belt From High Range to LOW Range Choosing Wheel Tine SpeedsMove the Wheels/Tines/PTO Drive Lever into Neutral Go to right side of tiller and finish seating the beltTilling depths Let the tiller do the workAvoid tilling wet, soggy soil To help avoid personal injury, be awareSuggested tilling patterns Avoid making footprintsTilling on slopes Tilling up and down slopesTerrace Gardening Clearing the tinesWide-Row Planting Power CompostingTilling Under Corn Soil Enrichment IdeaRemoving Tine Attachment Removing And Replacing The Tine AttachmentMove the tiller to level ground To Avoid Personal Injury or Damage to EquipmentSetting Up Stationary Attachments Installing the Tine AttachmentGuide Pin Mounting Hole Move the two swing-bolts intoStarting The Engine Setting Up Non-Powered Attach- mentsOperating Stationary Attachments Stopping the EngineProcedure EveryHours Tiller Lubrication Tighten Bolts and NutsChecking the Power Unit Oil Level Transmission Gear Oil MaintenanceChecking for Oil Leaks Checking Gear Oil LevelsChecking the Tine Attachment Oil Level Adding or Changing Gear OilFor Dipsticks With Hot/Cold Markings If the level is incorrect, see Adding or Changing Gear OilDraining and Filling PTO Power Unit Transmission Adding Gear Oil to PTO Power Unit TransmissionAdding Gear Oil to the Tine Attachment Transmission Draining and Filling the Tine Attachment TransmissionMeasuring and Adjusting Drive Belt Tension Drive Belt MaintenanceHow to Measure Belt Tension Belt Adjustment ToolReplacing the Drive Belt Removing the BeltReplacing the Drive Belt Reverse Disc Inspection Reverse Drive System MaintenanceInstalling a New Reverse Disc Checking and Adjusting Reverse the Drive SystemChecking and Adjusting Reverse Disc Replacing the Reverse DiscBolo Tine Maintenance Adjusting Reverse DriveChecking Tines for Wear Removing and Replacing a Tine Holder Assembly Single Tine ReplacementRemoving Tine Holder Assembly Replacing Tines Holder AssemblyTire and Wheel Maintenance Tine Shaft MaintenanceAir Cleaner Maintenance Spark Plug MaintenanceInspecting Forward Interlock Wiring System Testing the Forward Interlock Wiring SystemStoring Your Tiller Troubleshooting Procedures LinkageEccentric Tiller Pulls To One Side Dozer/Snow Blade Attachment Troy-BiltPTO Log SplitterWrap-Around Bumper Guard Hiller/Furrower AttachmentPart Description DescriptionDescription QTY Models 682J. E686N & E682L1186246 725-0157GW-9250 Handlebar Switch-forward GW-2551 Handlebar Wire Harness AssyGW-9548 GW-9119GW-1113-1 710-3005712-3017 GW-20795Wheel Speed LEVER, Belt Drive SYSTEM, ENGINES, Wheels Belt Drive System Wheel Speed LeverEngines and Engine Mount Wheel & Tire AssembliesPower Unit Transmission Assemblies Drive Shaft Assembly Pinion Shaft AssemblyBracket Assemblies Models 682J & E682L FromTransmission Assembly Transmission HousingPart Description QTY Miscellaneous PartsParts List Transmission Housing and Dipstick Tiller Drive Shaft AssemblyBolo Tine Assemblies Description QTY Custom Tilling Tines Standard Tilling TinesModels E686N & E682L GW-2614 Battery Hold-down Clamp-with GW-96515 Cable-battery, positive and negative1908118 Wire Harness & Connecting GW-97020710-3181 Bumper Attachment. Includes Ref. Nos through 1910730736-0921 1909748Page Page Page TROY-BILT Tiller Lifetime Limited Warranty
Top Page Image Contents