Genie 114002 manual Electrocution Hazards, Tip-over Hazards

Page 4

Operator’s Manual

Third Edition • First Printing

 

 

 

 

SAFETY RULES

Electrocution Hazards

This machine, even with an optional fiberglass platform, is not electrically insulated and will not provide protection from contact with or proximity to electrical current.

Keep away from the machine if it contacts energized power lines or becomes electrically charged. Personnel on the ground or in the platform must not touch or operate the machine until energized power lines are shut off.

Maintain safe distances from electrical power lines and apparatus in accordance with applicable governmental regulations and the following chart.

 

Minimum Safe

Voltage

Approach Distance

Phase to Phase

Feet

Meters

0 to 300V

Avoid Contact

Allow for platform movement, electrical line sway or sag and movement due to strong or gusty winds.

Do not use the machine as a ground for welding.

Do not operate an AC powered machine or a DC battery charger unless using a 3-wire grounded extension cord connected to a grounded AC circuit. Do not alter or disable 3-wire grounded plugs.

Tip-over Hazards

Do not raise the platform unless the base is level, all four outriggers are properly installed and the leveling jacks firmly contact the floor.

Do not adjust or remove the outriggers while the platform is occupied or raised.

Do not move the machine while the platform is raised.

300V to 50KV

10

3.05

50KV to 200KV

15

4.60

200KV to 350KV

20

6.10

350KV to 500KV

25

7.62

 

 

 

500KV to 750KV

35

10.67

 

 

 

750KV to 1000KV

45

13.72

 

 

 

Do not place ladders or scaffolds in the platform or against any part of this machine.

Do not place or attach overhanging loads to any part of this machine.

Do not transport tools and materials unless they are evenly distributed and can be safely handled by the person in the platform.

2

Genie AWP Super Series

Part No. 114002

Image 4
Contents Operator’s Manual Contents Contact usSafety Rules Do Not Operate UnlessElectrocution Hazards Tip-over HazardsMaximum allowable side force Fall Hazards Collision HazardsImproper Use Hazard Bodily Injury HazardExplosion and Fire Hazard Damaged Machine HazardsExplosion Hazards Battery and Charger Safety DC Models Burn HazardsLifting Hazard Decal Legend Ground Controls ControlsAC and DC Models Air Models Platform Controls Page Breather Cap AC & DC Models Pre-operation InspectionFundamentals Pre-operation Inspection PRE-OPERATION InspectionCheck the Battery DC Models MaintenanceObserve and Obey Check the Hydraulic Oil Level Check the Tire Pressure RT Base ModelsCheck the Oil Lubricator Canister Drip Rate Air Models Scheduled MaintenanceCheck the Air Filter/Regulator Canister Air Models Function Tests Function Tests Setup Test Emergency StopTest Outrigger Interlock Workplace Inspection Workplace InspectionOperating Instructions Emergency Stop Platform Raise and LowerManual Lowering Auxiliary Platform Lowering AC & DC ModelsBattery Charging Instructions Battery and Charger Instructions Observe and ObeyTo Charge Battery Dry Battery Filling Charging InstructionsTransport Instructions Observe and Obey Transport InstructionsLifting Instructions Loading for Transport Transport InstructionsWinching the Machine onto a Flatbed Truck Securing the MachineLoading the Machine With a Crane Tilt-back Operation Instructions Observe and obey Tilt-back Operation InstructionsTilt-back Frame Lowering the Tilt-back Assembly Tilting Back the MachineStowing the Tilt-back Assembly Returning the Machine to Standing PositionDecals Inspection for Decals with WordsModels with Tilt-back Frame Models without Tilt-back Frame Inspection for Decals with Symbols Models with Tilt-back Frame Models without Tilt-back Frame Specifications Machine SpecificationsSpecifications Genie Scandinavia