Subaru Robin Power Products RGV12100 Gfci Receptacle, Connecting to Domestic Circuit House Wiring

Page 16

GFCI RECEPTACLE

After starting the engine, check the GFCI for proper functioning by the following test procedure.

■

■

■

Push blue TEST button, The red RESET button will pop out exposing the word TRIP. Power is now off at the outlets protected by the GFCI, indicating that the device is functioning prop- erly.

If TRIP dose not appear when testing, do not use the generator. Call a qualified electrician.

To restore power, push RESET button.

WARNING

If the RESET button pops out during operation, stop the generator immediately and call a qualified electrician for checking generator and the appliances.

CONNECTING TO DOMESTIC CIRCUIT (HOUSE WIRING)

WARNING

This generator is neutral grounded type.

If a generator is to be connected to residential or commercial power lines, such as a stand-by power source during power outage, all connections must be made by a licensed electrician.

Failure in connection may result in death, personal injury, damage to generator, dam- age to appliances, damage to the building's wiring or fire.

(a)When connecting a Robin generator to a house wiring, generator output power must be taken from the 240V-4P receptacle.

(b)Install a transfer switch.

A transfer switch must be installed to transfer the load from the commercial power source to the generator. This switch is necessary to prevent accidents caused by the recovery from power outage. Use a transfer switch of the correct capacity.

Install transfer switch between the meter and the fuse or AC breaker box.

［CAUTION］

If the neutral wire of house wiring is grounded, be sure to ground the ground terminal of the generator, Otherwise an electric shock may occur to the operator.

－ 13－

Image 16

Contents Generators Contents － 04－ Specifications － 1－Performance Curves － 2－General Description of Generator － 3－Control Panel － 4－Serial Number － 5－Stator Construction and Function－ 6－ Rotor Brush / Brush HolderCurrent Transformer Diode Unit RGV13100T onlyECU Electronic Control Unit 5 A.V.R Automatic Voltage Regulator RGV12100 only－ 8－ Idle Control Unit RGV12100 only － 9－OIL Pressure Switch AC Switch NO-FUSE BreakerRelief Valve － 10－RGV13100T AC Receptacle－ 11－－ 12－ AC plug DescriptionGfci Receptacle Connecting to Domestic Circuit House Wiring－ 13－－ 14－－ 15－ AC Three Phase Receptacle RGV13100T only － 16－Description of Generator Operation Primary Exciting Action RGV12100Voltage Regulating Mechanism RGV12100 － 17－Advantages of Current Transformer Control RGV13100T Current Transformer Control RGV13100T－ 18－ Safety Precautions Do not place inflammable materials near the generatorOperate the generator on a level surface Do not operate with wet hands or in the rainIncandescent lamp, heater, etc. with a power factor Range of ApplicationsMotor driven tools and light electrical appliances － 20－Appliances without any indication as to power consumption － 21－－ 22－ Measuring Instruments Measuring Procedures－ 23－ AC Output Measuring － 24－Stator Measuring Insulation Resistance－ 25－ Rotor Control PanelCurrent Transformer RGV13100T － 26－Checking Functional Members Pilot Lamp and VoltmeterAC Receptacles － 27－RGV12100 － 28－Exciting Coil RGV12100 only Rotor Assembly－ 29－ Brush A.V.RAutomatic Voltage Regulator － 30－Current Transformer RGV13100T only － 31－RGV12100 only Idle Control Unit－ 32－－ 33－ Disassembly and Assembly Preparation and PrecautionsDisassembly Procedures Control Panel AlternatorComponent Parts － 35－Generator assembly Control Box RGV12100 Control Box RGV13100T Fuel Tank Generator Assembling Procedures Front Cover － 40－－ 41－ Rear Cover － 42－－ 43－ Troubleshooting No AC outputAC Voltage is too high or too low Check engine speed Check if engine is overheatedEngine dose not run － 45－Wiring Diagram － 46－－ 47－ Lively Blvd. Wood Dale, IL 60191 Phone 630-350-8200 Fax