Subaru Robin Power Products 13100T, RGV12100 Generator Assembling Procedures Front Cover, － 40－

Page 43

9-4 GENERATOR ASSEMBLING PROCEDURES

9-4-1 FRONT COVER

Attach the front cover to the engine main bearing cover. Match the faucet joint and tighten the bolts.

Tightening torque

230-250 kg cm

22.5-24.5 Nm

16.6-19.5 ftlbs

FRONT COVER

WASHER

SPRING WASHER

BOLT

Fig. 9-5

9-4-2 ROTOR

(1)Wipe off oil, grease and dust from the tapered portion of engine shaft and matching tapered hole of rotor shaft.

(2)Mount the rotor to the engine shaft. Tighten the through bolt.

Tightening torque

120 -140 kgcm

11.8-13.7 Nm 8.7-10.1 ftlbs

BEARING

ROTOR

THROUGHBOLT

SPRINGWASHER

 

Fig. 9-6

－ 40－

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Generators Contents － 04－ － 1－ Specifications－ 2－ Performance Curves－ 3－ General Description of Generator－ 4－ Control Panel－ 5－ Serial NumberStator Construction and Function－ 6－ Diode Unit RGV13100T only RotorBrush / Brush Holder Current TransformerECU Electronic Control Unit 5 A.V.R Automatic Voltage Regulator RGV12100 only－ 8－ － 9－ Idle Control Unit RGV12100 only－ 10－ OIL Pressure SwitchAC Switch NO-FUSE Breaker Relief ValveRGV13100T AC Receptacle－ 11－ AC plug Description － 12－Gfci Receptacle Connecting to Domestic Circuit House Wiring－ 13－ － 14－ － 15－ － 16－ AC Three Phase Receptacle RGV13100T only－ 17－ Description of Generator OperationPrimary Exciting Action RGV12100 Voltage Regulating Mechanism RGV12100Advantages of Current Transformer Control RGV13100T Current Transformer Control RGV13100T－ 18－ Do not operate with wet hands or in the rain Safety PrecautionsDo not place inflammable materials near the generator Operate the generator on a level surface－ 20－ Incandescent lamp, heater, etc. with a power factorRange of Applications Motor driven tools and light electrical appliances－ 21－ Appliances without any indication as to power consumption－ 22－ Measuring Instruments Measuring Procedures－ 23－ － 24－ AC Output MeasuringStator Measuring Insulation Resistance－ 25－ － 26－ RotorControl Panel Current Transformer RGV13100T－ 27－ Checking Functional MembersPilot Lamp and Voltmeter AC Receptacles－ 28－ RGV12100Exciting Coil RGV12100 only Rotor Assembly－ 29－ － 30－ BrushA.V.R Automatic Voltage Regulator－ 31－ Current Transformer RGV13100T onlyRGV12100 only Idle Control Unit－ 32－ － 33－ Alternator Disassembly and AssemblyPreparation and Precautions Disassembly Procedures Control Panel－ 35－ Component PartsGenerator assembly Control Box RGV12100 Control Box RGV13100T Fuel Tank － 40－ Generator Assembling Procedures Front Cover－ 41－ － 42－ Rear Cover－ 43－ Check if engine is overheated TroubleshootingNo AC output AC Voltage is too high or too low Check engine speed－ 45－ Engine dose not run－ 46－ Wiring Diagram－ 47－ Lively Blvd. Wood Dale, IL 60191 Phone 630-350-8200 Fax
Top Page Image Contents