Subaru Robin Power Products 13100T service manual RGV12100, － 28－

Page 31

8-3 AC SWITCH (NO-FUSE BREAKER)

Check continuity between each of 2 terminals at the back side of AC switch (no-fuse breaker) while it is mounted on the control panel.

Normally, there is continuity between each of the 2 terminals when the breaker is ON, while no continuity when the breaker is OFF.

RGV12100

8-4 STATOR

RGV13100T

Disengage connectors on the wires from stator and check the resistance between wires with a circuit tester, referring to the following specification table.

NOTE : If the circuit tester is not sufficiently accu- rate, it may not show the values given and may give erroneous readings.

Erroneous readings will also occur when there is a wide variation of resistance among coil windings or when measure- ment is performed at ambient tempera- tures different from 20℃

(68 °F).

					Stator coil
	Model	Hz/Voltage
	Model	Hz/Voltage	Red-White	Black-Blue	Black-Red	White-	Black-White
						White-
						Light green
						Light green

	RGV12100	60/120/240	0.11Ω	0.11Ω	------------	0.37Ω	------------

	RGV13100T	60/120/208	0.23Ω	------------	0.23Ω	------------	0.23Ω

－ 28－

Image 31

Contents Generators Contents － 04－－ 1－ Specifications－ 2－ Performance Curves－ 3－ General Description of Generator－ 4－ Control Panel－ 5－ Serial NumberStator Construction and Function－ 6－ Diode Unit RGV13100T only RotorBrush / Brush Holder Current TransformerECU Electronic Control Unit 5 A.V.R Automatic Voltage Regulator RGV12100 only－ 8－－ 9－ Idle Control Unit RGV12100 only－ 10－ OIL Pressure SwitchAC Switch NO-FUSE Breaker Relief ValveRGV13100T AC Receptacle－ 11－ AC plug Description － 12－Gfci Receptacle Connecting to Domestic Circuit House Wiring－ 13－－ 14－－ 15－－ 16－ AC Three Phase Receptacle RGV13100T only－ 17－ Description of Generator OperationPrimary Exciting Action RGV12100 Voltage Regulating Mechanism RGV12100Advantages of Current Transformer Control RGV13100T Current Transformer Control RGV13100T－ 18－ Do not operate with wet hands or in the rain Safety PrecautionsDo not place inflammable materials near the generator Operate the generator on a level surface－ 20－ Incandescent lamp, heater, etc. with a power factorRange of Applications Motor driven tools and light electrical appliances－ 21－ Appliances without any indication as to power consumption－ 22－ Measuring Instruments Measuring Procedures－ 23－－ 24－ AC Output MeasuringStator Measuring Insulation Resistance－ 25－－ 26－ RotorControl Panel Current Transformer RGV13100T－ 27－ Checking Functional MembersPilot Lamp and Voltmeter AC Receptacles－ 28－ RGV12100Exciting Coil RGV12100 only Rotor Assembly－ 29－－ 30－ BrushA.V.R Automatic Voltage Regulator－ 31－ Current Transformer RGV13100T onlyRGV12100 only Idle Control Unit－ 32－－ 33－ Alternator Disassembly and AssemblyPreparation and Precautions Disassembly Procedures Control Panel－ 35－ Component PartsGenerator assembly Control Box RGV12100 Control Box RGV13100T Fuel Tank － 40－ Generator Assembling Procedures Front Cover－ 41－－ 42－ Rear Cover－ 43－ Check if engine is overheated TroubleshootingNo AC output AC Voltage is too high or too low Check engine speed－ 45－ Engine dose not run－ 46－ Wiring Diagram－ 47－ Lively Blvd. Wood Dale, IL 60191 Phone 630-350-8200 Fax