Husqvarna EU1130STE To remove belt cover, Entfernen der riemenabdeckung, To replace belts

Page 47

To remove belt cover

B

1. Remove the two (2) screws (A) securing belt cover (B) to frame (C).

 

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten se-

curely.

Entfernen der riemenabdeckung

1.Entfernen Sie die zwei (2) Schrauben (A), mit denen die Riemena- beckung (B) am Rahmen (C) befestigt ist.

2. Entfernen Sie die Riemenabdeckung.

C A

•Befestigen Sie die Riemenabdeckung erneut, indem Sie die Abdeck- ung und die Schrauben wieder anbringen und die Schrauben fest anziehen.

Pour enlever le couvercle de la courroie

1.Enlevez les deux (2) vis (A) en fi xant le couvercle de la courroie (B) au châssis (C).

2.Enlevez le couvercle de la courroie.

•Remplacez le couvercle de la courroie en installant le couvercle et serrez solidement.

Desmontar el cubre correas

1.Desmontar los dos (2) tornillos (A) que sujetan el cubre correas (B) a la carcasa (C).

2.Desmontar el cubre correas.

•Sustituir el cubre correas colocando la cubierta y los tornillos y apretando fi rmemente.

Het verwijderen van de riemhuls

1.Verwijder de twee (2) schroeven (A) die de riemhuls (B) aan het frame (C) bevestigen.

2.Verwijder de riemhuls.

•Zet de riemhuls weer terug door de huls en de schroeven terug te plaatsen en draai stevig aan.

Rimuovere il coperchio della cinghia

1.Togliere le due (2) viti (A) che fi ssano il coperchio della cinghia (B) all’intelaiatura (C).

2.Togliere il coperchio della cinghia.

•Rimettere coperchio e viti, stringendo bene.

21

 

3

 

L

 

K

 

A

 

D

 

C

 

B

J

H

 

M

E

F

G

21

To replace belts

The auger and traction drive belts are not adjustable. If the belts are dam- aged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a qualifi ed service center.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing (1) from the frame assembly (2), it is important that an assistant stand in the oper- ating position and hold the snow thrower handles (3). Serious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, outdoors, away from fi re or fl ame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen lock nut securing chute rota- tor head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY (A) - Remove bolt (B), lock washer (C) and fl at washer (D) securing pulley to engine crankshaft. Remove outside (auger) pulley (A) only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two bolts (F) and lock washers (G) holding auger housing (1) and frame (2) together.

WARNING: As the last bolt is removed, have your assistant care- fully lower the handles down to the ground.

6.REMOVE AUGER BELT (H) from around pulley (E).

7.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER (J) and remove traction drive belt (K) from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm (J) and rotate ratchet clockwise to relieve tension.

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents EU5524ST EU8024STE, EU1130STE Contents Sichere Bedienung einer Schnee- fräse Préparation BedienungWartung und Lagerung InstructionsFormación Técnicas de funcionamiento seguro para máquinas quitanievesFonctionnement Entretien et rangementVoorbereiding FuncionamientoMantenimiento y Conservación InstructiesPreparazione Procedure di sicurezza per l’utilizzo di spazzaneveOnderhoud en Opslag AddestramentoManutenzione e conservazione EU8024STE EU1130STE Sacar la máquina quitanieves del cartón Remove snow thrower from the cartonEntnehmen der Schneefräse aus dem Karton Enlever la souffleuse de la caisse en cartonComo preparar su máquina quita- nieves How to set up your snow throwerComment installer votre souffleuse Zusammensetzen der SchneefräseHet uitpakken van de bovenste hendel Het installeren van de staaf van de snelheidsregelingInstall traction drive control rod Installation des fahrantriebssteuerhebelsHet installeren van de regelstang van de boorre- geling Install auger control rodInstallation des Steuerhebels für die einzugssch- necken Installez la tige de contrôle de la vis sans finFür die auswurfrinne Install discharge chute / chute rotater headInstallation der auswurfrinne / der drehvorrichtung Het installeren van de afvoertrechter / rotorkopEU8024STE, EU1130STE G K a Werkzeugkasten Como utilizar su máquina quita- Nieves How to use your snow throwerBedienung der schneefräse Comment utiliser votre souffleuseUso della valvola di arresto del combustibile F Pour utiliser la commande des gaz CPour utiliser la commande d’étrangleur E Hoe de afsluitklep van de brandstoftank F te gebruikenPour contrôler la décharge de la neige EU5524ST EU8024STE, EU1130STETo control snow discharge Regelung des schneeauswurfsRegolare la bocca di scarico della neve Controlar la eyección de la nieveHet bedienen van de sneeuwuitstoot Pour lancer de la neige Using the clean-out toolTo throw snow Das schneefräsenUtilizzo dello strumento di pulitura Utilisation de l’outil de nettoyageUsar la herramienta para la limpieza De ontstopper gebruikenHandle To move forward and backwardVorwärts und rückwärts fahren Moverse adelante y atrásEU1130STE Schaber P To adjust skid plates NScraper bar P Einstellen der gleitkufen NPer regoalre la piastra di slittamento N Regular las placas de deslizamiento NBarra de arrastre P Het afstellen van de remplaten NCortadores de Acumulaciones AA Drift Cutters AAWehenschneider AA Coupeurs de Dérive AAVoordat U DE Motor Start VOR DEM MotorstartAvant DE Mettre LE Moteur EN Marche Antes DE Poner EN Marcha EL MotorMotor anlassen To start engineBefore stopping If recoil starter has frozenPour mettre le moteur en marche Vor dem ausschaltenWenn der anreißstarter eingefroren ist Antes de parar Avant l’arrêtSi le démarreur manuel a gelé Puesta en marcha del motorAls de terugloopstarter is bevroren Si el arrancador de retroceso se ha con- geladoDe motor starten Voordat u stoptSe il motorino di avviamento a strappo si gela Avviare il motorePrima dell’arresto Consejos para lanzar la nieve Snow throwing tipsHinweise für das schneefräsen Conseils pour le soufflage de la neigeWartungsnachweis Service RecordTips voor het sneeuwruimen Consigli per spazzare la neveDati di servizio Schema dentretienService aantekeningen Informe de servicioCourroies en Transmission du dispositif de déplacementGetriebegehäuse der einzugsschnecken FahrantriebssystemMotor EngineMoteur Motore Limpieza CleaningReinigung NettoyageSpazzaneve SouffleuseMáquina Quitanieves SneeuwruimerScherbolzen Shear boltsPernos de seguridad F C Vis de cisaillementPerni di sicurezza SchuifboutenDesmontar el cubre correas To remove belt coverEntfernen der riemenabdeckung Pour enlever le couvercle de la courroieErneuern der riemen Pour remplacer les courroies Het vervangen van de riemen Sustituir las correasMontaggio Della Puleggia DEL Motore a Sostituire le cinghieHET Verwijderen VAN DE Motorriemschijf Togliere LA Cinghia Della Coclea H dalla puleg- gia EEU5524ST, EU8024STE Engine Motor Sonstiges StorageOther LagerungDivers EntreposageAlmacenaje SouffleuseAltro OpslagOverig ImmagazzinaggioStörungssuche TroubleshootingRecherche des causes d’une panne Solución de problemasHET Probleem DE Oorzaak DE Oplossing Probleemoplosser532 40 80-34 07.31.06 by

EU1130STE, EU5524ST, EU8024STE specifications

Husqvarna is renowned for its cutting-edge outdoor power equipment, and among its impressive offerings are the EU8024STE, EU5524ST, and EU1130STE models. Each of these snow throwers is designed to provide exceptional performance and lasting durability, making them ideal for tackling winter weather challenges.

The Husqvarna EU8024STE is a powerful snow thrower designed for heavy-duty use. Equipped with a robust 24-inch clearing width, it is capable of handling large amounts of snow efficiently. Its advanced electric start feature ensures that you can quickly get to work, even in the coldest conditions. This model features a high-performance engine that delivers optimal power and speed, making quick work of thick snow drifts. The dual-stage system enhances its ability to throw snow at impressive distances, and the adjustable chute allows for precise snow placement.

Next in line is the EU5524ST, which offers a balance between power and maneuverability. With a 24-inch clearing width, this model is ideal for residential use. It is powered by a dependable engine that ensures reliable performance without sacrificing ease of use. The EU5524ST features an efficient single-stage design, which makes it lighter and more agile while still being able to clear snow effectively. The user-friendly controls and the ergonomic handle contribute to a more comfortable experience during extended use.

Lastly, the Husqvarna EU1130STE stands out with its impressive clearing capabilities. With a larger 30-inch clearing width, this model is perfect for larger driveways and commercial applications. The dual-stage system, combined with its powerful engine, allows it to handle heavy snowfalls with ease. The EU1130STE also includes impressive features such as heated handles for added comfort during operation and LED headlights, ensuring visibility even in low-light conditions. The adjustable skid shoes also allow users to customize the height for different surfaces, making it versatile for use on various terrains.

Overall, the Husqvarna EU8024STE, EU5524ST, and EU1130STE snow throwers each bring their unique strengths to the table, catering to different user needs. Their innovative features and reliable performance ensure that snow removal becomes a hassle-free task, empowering users to conquer winter's challenges with confidence and efficiency. Whether for residential or commercial use, these models reflect Husqvarna's commitment to quality and innovation in outdoor power equipment.
Top Page Image Contents