Intel SE7500CW2 manual Dual Processor Operation, Boxed Processor Fan Heat sink

Page 11

Processor

The Server Board SE7500CW2 accommodates two Intel Xeon processors with 512 KB cache. The SKT604 is a 604-pin zero-insertion force (ZIF) socket. The processor(s) interface with the system bus at 400 MHz.

For a complete list of supported processors, see:

http://support.intel.com/support/motherboards/server/SE7500CW2

Dual Processor Operation

The Intel Xeon interface is dual processor (DP) ready. Each processor contains a local

Intel® Advanced Programmable Interrupt Controller (APIC) section for interrupt handling. When two processors are installed, both processors must be of identical revision, core voltage, and bus/core speeds.

Boxed Processor Fan Heat sink

A processor wind tunnel is supplied with the boxed Intel Xeon processor. After the processor and heat sink are installed, install and connect the processor wind tunnel. For proper processor cooling, the fan inlet air temperature should be below 45 °C.

CAUTION

Clearance is required at each end of the fan heat sink to ensure unimpeded airflow for proper cooling. Restricting the airflow through the processor heat sink can cause overheating and subsequent failure of the processor.

Description

11

Image 11
Contents Intel Server Board SE7500CW2 Product Guide Disclaimer Contents Upgrading Solving ProblemsIndex Technical ReferenceRegulatory and Integration Information Tables Description Server Board FeaturesServer Board Features FeatureSystem I/O Power Security Form Factor Back Panel Connectors Back Panel ConnectorsServer Board Connector and Component Locations Server Board Connector and Component LocationsBoxed Processor Fan Heat sink ProcessorDual Processor Operation MCH Intel E7500 ChipsetParallel Port Keyboard and Mouse ConnectorsSuper I/O Serial PortsPCI I/O Subsystem MemoryBit / 100 MHz PCI-X Capable Subsystem Bit / 133 MHz PCI-X Capable Subsystem32-bit/33 MHz PCI Subsystem Video ControllerNetwork Interface Controller NIC Wake on LAN AC Link ModeSecurity Operation Summary Password ProtectionSecurity Using Passwords Password Clear JumperIntel Server Board SE7500CW2 Product Guide Description and brief procedure Configuration Software and UtilitiesPower-On Self-Test Post Configuration UtilitiesSetup Menus Using Bios Setup UtilityIf You Cannot Access Setup Starting SetupPress Keyboard CommandsMenu Selection Bar Main Advanced Security Power Boot SystemMenu Selection Bar On-Screen OptionsChoices 44 MB, 3 ½ defaultMain Menu Main MenuPrimary/Secondary, Master/Slave Submenu Disabled defaultEnabled default Description Primary/Secondary, Master/Slave SubmenusAdvanced Menu Win2000/.NET DefaultAdvanced Menu Enabled default Disabled default No defaultDOS default Auto Detect defaultO Device Configuration Submenu Device Configuration SubmenuDMA 3 default ECP default DefaultIRQ7 default On Board Device Submenu On Board Device SubmenuPCI Configuration Submenu PCI Configuration SubmenuOption ROM Scan Submenu Choices Enabled defaultChoices Disabled default Server Menu SubmenuConsole Redirection Submenu Console Redirection SubmenuEvent Logging Submenu Enabled default No defaultEvent Logging Submenu Hardware Monitor Submenu Hardware Monitor SubmenuSecurity Menu If no password entered previously FeatureEnabled default User default Security MenuLast State default Power MenuBoot Menu Power MenuDevice Boot MenuBoot Priority System Menu Feature ChoicesSystem Menu Exit Menu Port On Board Connector DesignatorExit Menu Obtaining the Upgrade Utility Upgrading the BiosPreparing for the Upgrade Recording the Current Bios SettingsCreating the Bios Upgrade Diskette Upgrading the BiosRecovering the Bios Changing the Bios Language Sensor Type Hardware MonitoringMonitored Headers and Sensors Intel Server Board SE7500CW2 Product Guide Before You Begin Server Board InstallationSafety Cautions Tools and Supplies NeededSafety and Regulatory Compliance Processor Installation NotesPower Supply Minimum Hardware RequirementsAttaching the Gasket to the I/O Shield Installation ProceduresInstalling the I/O Gasket and Shield Attaching the Label to the I/O Shield Installing the I/O ShieldConfiguring Chassis Standoffs Configuring Chassis StandoffsInstalling Rubber Bumpers Installing Rubber BumpersAttaching the Server Board Installing the Server BoardPlacing the Server Board into the Chassis Installing Memory Installing MemoryInstalling the Retention Brackets Installing the ProcessorsApplying Thermal Grease Attaching the ProcessorAttaching the Heat Sink Installing the Processor Wind TunnelAttaching the Processor Wind Tunnel Assembly Attaching Intake and Exhaust Assemblies Attaching the Heat Sink FanInstalling the Optional Scsi Add-in Card Making Connections to the Server Board Making Connections to the Server BoardIDE Cables Cable RoutingRouting the Floppy Drive Cable Floppy Drive CableMaking Back Panel Connections Finishing UpUpgrading Memory Installing DIMMsProcessors Adding or Replacing a Processor Attaching the Processor Installing the Processor Wind Tunnel OM14477 Removing a Processor Replacing the Backup BatteryVarning Intel Server Board SE7500CW2 Product Guide Initial System Startup Solving ProblemsResetting the System ChecklistAfter the System Has Been Running Correctly Running New Application SoftwareMonitoring Post More Problem Solving ProceduresPreparing the System for Diagnostic Testing Confirming Loading of the Operating System Specific Problems and Corrective ActionsPower Light Does Not Light Verifying Proper Operation of Key System LightsCharacters Are Distorted or Incorrect No Characters Appear on ScreenDiskette Drive Activity Light Does Not Light System Cooling Fans Do Not Rotate ProperlyCannot Connect to a Server Problems with NetworkHard Disk Drive Activity Light Does Not Light CD-ROM Drive Activity Light Does Not LightPCI Installation Tips Problems with Application SoftwareBootable CD-ROM Is Not Detected World Wide Web Telephone Getting HelpIntel Server Board SE7500CW2 Product Guide Jumper Name Configuration JumpersPins What happens at system reset Technical ReferenceLocation Pins DescriptionFront Panel Header Front Panel Header Connection DescriptionsProduct EMC Compliance Product Safety ComplianceRegulatory and Integration Information Product Regulatory ComplianceProduct Certification Markings Electromagnetic Compatibility NoticesProduct Regulatory Compliance Markings Taiwan Declaration of Conformity Europe CE Declaration of ConformityAustralia / New Zealand Korean RRL ComplianceESD IndexPCI
Related manuals
Manual 17 pages 57.58 Kb