Intel SE7500CW2 manual Installing the Optional Scsi Add-in Card

Page 60

Installing the Optional SCSI Add-in Card

Certain versions of the Server Board SE7500CW2 ship with an Ultra160 SCSI card. This card has the following features:

•Ultra160 single channel based on the LSI† 53C1000 SCSI controller

•PCI 2.2 compliant

•PCI 64-bit/66 MHz

•Universal PCI form factor

•Low profile form factor, shipping with a full-size bracket attached and a low-profile bracket in the packaging

•Internal and external connectors (internal standard 68 pin HD, external VHDI connector)

•Termination: Universal (LVD/SE) termination, automatic cable detection, software disable

•Four-pin header for off-board LEDs

Drivers for this card can be downloaded from the Server Board SE7500CW2 System Resource CD that ships with the board or from the Server Board SE7500CW2 Intel Support Web site:

http://support.intel.com/support/motherboards/server/SE7500CW2

✏NOTE

In order to maximize airflow within the chassis, it is recommended that you install the SCSI add-in card in either PCI slot 2 or 3 and install SCSI devices in the chassis lower device bays. However, the SCSI add-in card can be installed in any PCI slot on the server board.

1.Remove the screw that secures the filter panel at PCI slot 2 or 3.

2.Remove the filter panel at PCI slot 2 or 3 by pushing it out from the inside of the chassis.

3.Insert the SCSI card.

4.Replace the screw.

60	Intel Server Board SE7500CW2 Product Guide

Image 60

Contents Intel Server Board SE7500CW2 Product Guide Disclaimer Contents Solving Problems UpgradingTechnical Reference Regulatory and Integration InformationIndex Tables Server Board Features Server Board FeaturesFeature DescriptionSystem I/O Power Security Form Factor Back Panel Connectors Back Panel ConnectorsServer Board Connector and Component Locations Server Board Connector and Component LocationsProcessor Dual Processor OperationBoxed Processor Fan Heat sink Intel E7500 Chipset MCHKeyboard and Mouse Connectors Super I/OSerial Ports Parallel PortMemory PCI I/O SubsystemBit / 133 MHz PCI-X Capable Subsystem Bit / 100 MHz PCI-X Capable SubsystemVideo Controller Network Interface Controller NIC32-bit/33 MHz PCI Subsystem AC Link Mode Wake on LANPassword Protection SecuritySecurity Operation Summary Password Clear Jumper Using PasswordsIntel Server Board SE7500CW2 Product Guide Configuration Software and Utilities Power-On Self-Test PostConfiguration Utilities Description and brief procedureUsing Bios Setup Utility If You Cannot Access SetupStarting Setup Setup MenusKeyboard Commands PressPower Boot System Menu Selection BarOn-Screen Options Menu Selection Bar Main Advanced Security44 MB, 3 ½ default Main MenuMain Menu ChoicesDisabled default Enabled default DescriptionPrimary/Secondary, Master/Slave Submenus Primary/Secondary, Master/Slave SubmenuWin2000/.NET Default Advanced MenuAdvanced Menu Disabled default No default DOS defaultAuto Detect default Enabled defaultDevice Configuration Submenu O Device Configuration SubmenuECP default Default IRQ7 defaultDMA 3 default On Board Device Submenu On Board Device SubmenuPCI Configuration Submenu PCI Configuration SubmenuChoices Enabled default Choices Disabled defaultServer Menu Submenu Option ROM Scan SubmenuConsole Redirection Submenu Console Redirection SubmenuEnabled default No default Event Logging SubmenuEvent Logging Submenu Hardware Monitor Submenu Hardware Monitor SubmenuIf no password entered previously Feature Enabled default User defaultSecurity Menu Security MenuPower Menu Boot MenuPower Menu Last State defaultBoot Menu Boot PriorityDevice Feature Choices System MenuSystem Menu Port On Board Connector Designator Exit MenuExit Menu Upgrading the Bios Preparing for the UpgradeRecording the Current Bios Settings Obtaining the Upgrade UtilityUpgrading the Bios Recovering the BiosCreating the Bios Upgrade Diskette Changing the Bios Language Hardware Monitoring Monitored Headers and SensorsSensor Type Intel Server Board SE7500CW2 Product Guide Server Board Installation Safety CautionsTools and Supplies Needed Before You BeginSafety and Regulatory Compliance Installation Notes Power SupplyMinimum Hardware Requirements ProcessorInstallation Procedures Installing the I/O Gasket and ShieldAttaching the Gasket to the I/O Shield Installing the I/O Shield Attaching the Label to the I/O ShieldConfiguring Chassis Standoffs Configuring Chassis StandoffsInstalling Rubber Bumpers Installing Rubber BumpersInstalling the Server Board Placing the Server Board into the ChassisAttaching the Server Board Installing Memory Installing MemoryInstalling the Processors Installing the Retention BracketsAttaching the Processor Applying Thermal GreaseInstalling the Processor Wind Tunnel Attaching the Processor Wind Tunnel AssemblyAttaching the Heat Sink Attaching the Heat Sink Fan Attaching Intake and Exhaust AssembliesInstalling the Optional Scsi Add-in Card Making Connections to the Server Board Making Connections to the Server BoardCable Routing IDE CablesFloppy Drive Cable Routing the Floppy Drive CableFinishing Up Making Back Panel ConnectionsUpgrading Installing DIMMs MemoryProcessors Adding or Replacing a Processor Attaching the Processor Installing the Processor Wind Tunnel OM14477 Replacing the Backup Battery Removing a ProcessorVarning Intel Server Board SE7500CW2 Product Guide Solving Problems Resetting the SystemChecklist Initial System StartupRunning New Application Software After the System Has Been Running CorrectlyMore Problem Solving Procedures Preparing the System for Diagnostic TestingMonitoring Post Specific Problems and Corrective Actions Power Light Does Not LightVerifying Proper Operation of Key System Lights Confirming Loading of the Operating SystemNo Characters Appear on Screen Characters Are Distorted or IncorrectSystem Cooling Fans Do Not Rotate Properly Diskette Drive Activity Light Does Not LightProblems with Network Hard Disk Drive Activity Light Does Not LightCD-ROM Drive Activity Light Does Not Light Cannot Connect to a ServerProblems with Application Software Bootable CD-ROM Is Not DetectedPCI Installation Tips Getting Help World Wide Web TelephoneIntel Server Board SE7500CW2 Product Guide Configuration Jumpers Pins What happens at system resetTechnical Reference Jumper NamePins Description Front Panel HeaderFront Panel Header Connection Descriptions LocationProduct Safety Compliance Regulatory and Integration InformationProduct Regulatory Compliance Product EMC ComplianceElectromagnetic Compatibility Notices Product Regulatory Compliance MarkingsProduct Certification Markings Europe CE Declaration of Conformity Taiwan Declaration of ConformityKorean RRL Compliance Australia / New ZealandIndex ESDPCI

Related manuals

Manual 17 pages 57.58 Kb