Eiki/Elf EIP-4500 Setting and Adjusting, Setting the Security, Projector Settings & Adjustments

Page 25

Setting and Adjusting the

Projector (Settings & Adjustments)

Example: “Picture” screen display for INPUT 1

On these screens, you can make projector settings or adjustments.You can set or adjust the following items :

•Picture Mode

•CLR Temp

•Bright Boost

•Progressive

•C.M.S. Adjustment

•DNR

•Signal Type

•Auto Sync

•Auto Sync Disp

•Audio Out

•Internal Speaker [OFF][ON]

•Resize

•OSD Display

•Video System (INPUT 4/5)

•Background

•Startup Image

•Eco Mode [OFF][ON]

•Auto Search [OFF][ON]

•Auto Power Off [OFF][ON]

•Lamp Mode

•Projection Mode

•Keylock Level

•Set Inputs

•RS-232C Speed

•Monitor Out (Standby)

•OSD Language

•Video Wall (See page 41.)

•Stack Setting (See page 38.)

Note

•If you click the “Refresh” button before the screen is displayed completely, an error mes- sage (“Server Busy Error”) will be displayed. Wait for a moment and then operate again.

•You cannot operate this page while the pro- jector is warming up.

•While the projector is in standby mode, you can only control “Power ON”.

•For details about each item, refer to the owner’s manual of the projector.

Controlling the Projector via LAN

Setting the Security

(Network – Security)

On this screen, you can make settings relat- ing to security.

	Items	Description
User Name		Setting of user name for
		security protection.

Password		Setting of password for
		security protection.

Accept IP		It is possible to set up to three
Address		IP addresses allowing connec-
		tion to the projector.

	All IP	No limits are set to IP addresses
	Addresses	connecting to the projector.

	From only	For security improvement, only an
	specific IP	IP address set by “Address 1-3”
	addresses	can be connected to the projector.

After clicking the “Apply” button, the set val- ues appear. Confirm that the values are set properly, and then click the “Confirm” button.

Note

•After setting items, wait for 10 seconds and then re-access.

•User Name and Password can be up to 8 characters.

•You can input the characters below : a-z, A-Z, 0-9, -, _

•To cancel User Name and Password, enter nothing and then press “Apply” button.

25

Image 25

Contents Setup Guide Standard Setup Front Projection Setting up the ScreenThrow Distance Screen Size and Projection DistanceF1.8-F2.0, f=25.6-31.3 mm Standard Zoom Lens Standard equipment with EIP-4500F2.5, f=11.6 mm Fixed Wide Lens AH-45201F2.5, f=21.2-25.8 mm Wide-zoom Lens AH-45301F2.4-F2.5, f=31.9-42.5 mm Tele-zoom Lens AH-45501F2.5, f=40.8-62.8 mm Tele-zoom Lens AH-45601F2.4-F2.5, f=62.1-97.8 mm Tele-zoom Lens AH-45701RGB Input Component Input Connecting Pin AssignmentsConnecting Pin Assignments Computer control Communication conditions RS-232C Specifications and CommandsBasic format W R CommandsReturn Input 5 Tint -30 +30 OK or ERR CLR Temp Connecting the projector to a computer Setting up the Projector Network EnvironmentTurn on the projector Turn on the computer Connecting the Pro- jector to a ComputerSetting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Controlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later Controlling the Projector Confirming the ProjectorStatus Status ControlSetting the Security Setting and AdjustingProjector Settings & Adjustments Network SecuritySetting for Sending E-mail when an Error Occurs Making General Settings for the Network NetworkMail Originator Settings GeneralMail Recipient Settings When Connecting Using RS-232C Setting the Projector Using RS-232C or TelnetInput setup and press the Enter key Input PJS11234 and press the Enter keyClickstartfrom theWindows desk- top and select Run When Connecting Using Telnet4User Name Factory default setting Not Re- quired Setup Menu Main MenuView Setting Detail List Controlling the Projector Using RS-232C or TelnetVView All Setting Set ItemsQuit without Saving Set Save Settings and QuitSSave & Quit Tings QQuit UnchangedDefault Gateway Setting IP Address SettingSubnet Mask Setting Password Setting User Name SettingProjector Name Setting RS-232C Baud Rate SetSetting Auto Logout Time Disconnecting All ConnecEntering Advanced Setup Menu Data Port SettingCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses Return to Default Settings Setting of Search PortReturn to Main Menu Stack Projection Projector 1 Master Setting up the Stack ProjectionProjector 2 Slave Turn off the both projectorsProjector Projector MasterSlave Hub Video Wall ProjectionSetting up the Video Wall Projection Basic Click Video Wall on the menu Access one of the four projectors via Internet ExplorerSelect 2 X 2 on Division Click the assigning button for the desired positionReturning to the Default Video Wall Setup Adjusting the Position Horizontally and VerticallyAssigning the Projected Image on the Video Wall Setup Select 1 X 1 on Division Click the assigning buttonVideo Wall Projection Projector Slave Setting up the Video Wall Projection ApplicationJectors as shown below Change the TCP/IP settings for the computer as shown belowProjector Master Projector 2 Slave Projector 3 SlaveClick Stack on the menu Select Slave on Stack Setting Click Stack on the menu Select Master on Stack SettingMake the IP address for each pro- jector as shown below Repeat the same procedure from the to 12 for the projector 3 When connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm Dimensions