Eiki/Elf EIP-4500 setup guide Access one of the four projectors via Internet Explorer

Page 43

1 Access one of the four projectors via Internet Explorer.

(See “Controlling the Projector Using Internet Explorer (Version 5.0 or later)” (page 23) for the details.)

2 Click “Video Wall” on the menu.

•“Video Wall” display will appear.

3 Select “2 X 2” on “Division”.

Video Wall Projection

4 Click the assigning button for the desired position.

•The projector will be assigned to the part of the video wall.

Note

•For more details on the assigned position and the actual position of the projector, see “Assigning the Projected Image on the Video Wall Setup” (page 44).

5 Repeat the same procedure from the step 1 to 4 for the other three projectors.

That completes the video wall setup. When the same image signal is input to all the projectors, the video wall projection starts.

1

2

3

4

1Selects a position for each projector. (the assigning buttons)

2Selects a number of positions where the video wall is divided.

3Displays the current status for the video wall setup.

4Adjusts the position of the projected image horizontally and vertically.

43

Image 43

Contents Setup Guide Standard Setup Front Projection Setting up the ScreenThrow Distance Screen Size and Projection DistanceF1.8-F2.0, f=25.6-31.3 mm Standard Zoom Lens Standard equipment with EIP-4500F2.5, f=11.6 mm Fixed Wide Lens AH-45201F2.5, f=21.2-25.8 mm Wide-zoom Lens AH-45301F2.4-F2.5, f=31.9-42.5 mm Tele-zoom Lens AH-45501F2.5, f=40.8-62.8 mm Tele-zoom Lens AH-45601F2.4-F2.5, f=62.1-97.8 mm Tele-zoom Lens AH-45701RGB Input Component Input Connecting Pin AssignmentsConnecting Pin Assignments Computer control Communication conditions RS-232C Specifications and CommandsBasic format W R CommandsReturn Input 5 Tint -30 +30 OK or ERR CLR Temp Connecting the projector to a computer Setting up the Projector Network EnvironmentTurn on the projector Turn on the computer Connecting the Pro- jector to a ComputerSetting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Controlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later Control Confirming the ProjectorControlling the Projector Status StatusNetwork Security Setting and AdjustingSetting the Security Projector Settings & AdjustmentsGeneral Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs Mail Originator SettingsMail Recipient Settings Input PJS11234 and press the Enter key Setting the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input setup and press the Enter keyClickstartfrom theWindows desk- top and select Run When Connecting Using Telnet4User Name Factory default setting Not Re- quired Setup Menu Main MenuSet Items Controlling the Projector Using RS-232C or TelnetView Setting Detail List VView All SettingTings QQuit Unchanged Save Settings and QuitQuit without Saving Set SSave & QuitDefault Gateway Setting IP Address SettingSubnet Mask Setting RS-232C Baud Rate Set User Name SettingPassword Setting Projector Name SettingData Port Setting Disconnecting All ConnecSetting Auto Logout Time Entering Advanced Setup MenuCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses Return to Default Settings Setting of Search PortReturn to Main Menu Stack Projection Turn off the both projectors Setting up the Stack ProjectionProjector 1 Master Projector 2 SlaveProjector Projector MasterSlave Hub Video Wall ProjectionSetting up the Video Wall Projection Basic Click the assigning button for the desired position Access one of the four projectors via Internet ExplorerClick Video Wall on the menu Select 2 X 2 on DivisionSelect 1 X 1 on Division Click the assigning button Adjusting the Position Horizontally and VerticallyReturning to the Default Video Wall Setup Assigning the Projected Image on the Video Wall SetupVideo Wall Projection Projector Slave Setting up the Video Wall Projection ApplicationProjector 3 Slave Change the TCP/IP settings for the computer as shown belowJectors as shown below Projector Master Projector 2 SlaveClick Stack on the menu Select Slave on Stack Setting Click Stack on the menu Select Master on Stack SettingMake the IP address for each pro- jector as shown below Repeat the same procedure from the to 12 for the projector 3 When connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm Dimensions