Eiki/Elf EIP-4500 setup guide Save Settings and Quit, Quit without Saving Set, SSave & Quit

Page 32

Controlling the Projector Using RS-232C or Telnet

Save Settings and Quit

([S]Save & Quit)

Save set values and quit menu.

▼SETUP MENU

---------------------------------	SETUP MENU--------------------------------
[1]IP Address	[2]Subnet Mask	[3]Default Gateway
[4]User Name	[5]Password
[6]RS-232C Baud Rate	[7]Projector Name
[A]Advanced Setup		[D]Disconnect All
[V]View All Setting	[S]Save & Quit	[Q]Quit Unchanged
setup>s		1
All Connection will be disconnect.
Continue(y/n)? y		2
Apply New setting...Done.

Quit without Saving Set-

tings ([Q]Quit Unchanged)

Quit menu without saving setting values.

▼SETUP MENU

---------------------------------	SETUP MENU--------------------------------
[1]IP Address	[2]Subnet Mask	[3]Default Gateway
[4]User Name	[5]Password
[6]RS-232C Baud Rate [7]Projector Name
[A]Advanced Setup		[D]Disconnect All
[V]View All Setting	[S]Save & Quit	[Q]Quit Unchanged
setup>q		1
Quit Without Saving(y/n)? y		2
Setting Unchanged.

1Enter “s” and press the “Enter” key.

2 Enter “y” and press the “Enter” key.

1Enter “q” and press the “Enter” key.

2 Enter “y” and press the “Enter” key.

32

Image 32

Contents Setup Guide Setting up the Screen Standard Setup Front ProjectionScreen Size and Projection Distance Throw DistanceStandard Zoom Lens Standard equipment with EIP-4500 F1.8-F2.0, f=25.6-31.3 mmFixed Wide Lens AH-45201 F2.5, f=11.6 mmWide-zoom Lens AH-45301 F2.5, f=21.2-25.8 mmTele-zoom Lens AH-45501 F2.4-F2.5, f=31.9-42.5 mmTele-zoom Lens AH-45601 F2.5, f=40.8-62.8 mmTele-zoom Lens AH-45701 F2.4-F2.5, f=62.1-97.8 mmConnecting Pin Assignments RGB Input Component InputConnecting Pin Assignments Basic format RS-232C Specifications and CommandsComputer control Communication conditions Commands W RReturn Input 5 Tint -30 +30 OK or ERR CLR Temp Setting up the Projector Network Environment Connecting the projector to a computerConnecting the Pro- jector to a Computer Turn on the projector Turn on the computerSetting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Version 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Confirming the Projector Controlling the ProjectorStatus Status ControlSetting and Adjusting Setting the SecurityProjector Settings & Adjustments Network SecurityMaking General Settings for the Network Network Setting for Sending E-mail when an Error OccursMail Originator Settings GeneralMail Recipient Settings Setting the Projector Using RS-232C or Telnet When Connecting Using RS-232CInput setup and press the Enter key Input PJS11234 and press the Enter keyWhen Connecting Using Telnet Clickstartfrom theWindows desk- top and select RunSetup Menu Main Menu 4User Name Factory default setting Not Re- quiredControlling the Projector Using RS-232C or Telnet View Setting Detail ListVView All Setting Set ItemsSave Settings and Quit Quit without Saving SetSSave & Quit Tings QQuit UnchangedSubnet Mask Setting IP Address SettingDefault Gateway Setting User Name Setting Password SettingProjector Name Setting RS-232C Baud Rate SetDisconnecting All Connec Setting Auto Logout TimeEntering Advanced Setup Menu Data Port SettingAccepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test Return to Main Menu Setting of Search PortReturn to Default Settings Stack Projection Setting up the Stack Projection Projector 1 MasterProjector 2 Slave Turn off the both projectorsSlave Projector MasterProjector Video Wall Projection HubSetting up the Video Wall Projection Basic Access one of the four projectors via Internet Explorer Click Video Wall on the menuSelect 2 X 2 on Division Click the assigning button for the desired positionAdjusting the Position Horizontally and Vertically Returning to the Default Video Wall SetupAssigning the Projected Image on the Video Wall Setup Select 1 X 1 on Division Click the assigning buttonVideo Wall Projection Setting up the Video Wall Projection Application Projector SlaveChange the TCP/IP settings for the computer as shown below Jectors as shown belowProjector Master Projector 2 Slave Projector 3 SlaveMake the IP address for each pro- jector as shown below Click Stack on the menu Select Master on Stack SettingClick Stack on the menu Select Slave on Stack Setting Repeat the same procedure from the to 12 for the projector 3 Troubleshooting When connecting the projector using serial-connectionTroubleshooting \ After the initialization, carry out setting again Dimensions Units inches mm