Eiki/Elf EIP-4500 Change the TCP/IP settings for the computer as shown below, Projector 3 Slave

Page 47

Video Wall Projection

■Preparation

•Follow the procedure below after setting up the basic connection.

•When “User Name” and “Password” have been set to the projector, reset them before the stack projection

setup. To set “User Name” and “Password”, use the same user name and password for both of the master and slave projectors. (See page 25.)

•Set “Data Port” with the same number for both of the master and slave projectors. (See page 26.)

Info

•Do not use network software or equipment while it is accessing the projector via the port of the same number used for the master or slave projector, otherwise you cannot properly control multiple projectors with one remote control.

1 Change the TCP/IP settings for the computer as shown below.

(See “Setting an IP Address for the Computer” on page 19 for the details.)

• IP address

: 192.168.150.2

• Subnet mask

: 255.255.255.0

• Default gateway : (Do not input any values.)

Note

•The TCP/IP settings shown are examples to make connections following the diagram.

•When using other equipment in the same network, be careful about the IP address overlap or other network settings.

•Consult your network administrator for as- sistance with the network settings.

2 Change the TCP/IP settings for

3 Connect the computer and the pro-

each projector as shown below.

(See “Setting up a Network Connection for the

jectors as shown below.

Projector” on page 21 for the details.)

 

• IP address

Projector 1 : 192.168.150.3

 

 

Projector 2

: 192.168.150.4

 

 

Projector 3

: 192.168.150.5

 

 

Projector 4

: 192.168.150.6

 

• Subnet mask

 

: 255.255.255.0

 

• Default gateway

: 0.0.0.0

 

Projector 1:

Master

Projector 2: Slave

LAN terminal

Computer

LAN cable

LAN terminal

Projector 3: Slave

LAN terminal

Hub

Projector 4: Slave

LAN cable (straight-through type)

LAN terminal

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Setup Guide Standard Setup Front Projection Setting up the ScreenThrow Distance Screen Size and Projection DistanceF1.8-F2.0, f=25.6-31.3 mm Standard Zoom Lens Standard equipment with EIP-4500F2.5, f=11.6 mm Fixed Wide Lens AH-45201F2.5, f=21.2-25.8 mm Wide-zoom Lens AH-45301F2.4-F2.5, f=31.9-42.5 mm Tele-zoom Lens AH-45501F2.5, f=40.8-62.8 mm Tele-zoom Lens AH-45601F2.4-F2.5, f=62.1-97.8 mm Tele-zoom Lens AH-45701RGB Input Component Input Connecting Pin AssignmentsConnecting Pin Assignments Basic format RS-232C Specifications and CommandsComputer control Communication conditions W R CommandsReturn Input 5 Tint -30 +30 OK or ERR CLR Temp Connecting the projector to a computer Setting up the Projector Network EnvironmentTurn on the projector Turn on the computer Connecting the Pro- jector to a ComputerSetting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Version 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Control Confirming the ProjectorControlling the Projector Status StatusNetwork Security Setting and AdjustingSetting the Security Projector Settings & AdjustmentsGeneral Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs Mail Originator SettingsMail Recipient Settings Input PJS11234 and press the Enter key Setting the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input setup and press the Enter keyClickstartfrom theWindows desk- top and select Run When Connecting Using Telnet4User Name Factory default setting Not Re- quired Setup Menu Main MenuSet Items Controlling the Projector Using RS-232C or TelnetView Setting Detail List VView All SettingTings QQuit Unchanged Save Settings and QuitQuit without Saving Set SSave & QuitSubnet Mask Setting IP Address SettingDefault Gateway Setting RS-232C Baud Rate Set User Name SettingPassword Setting Projector Name SettingData Port Setting Disconnecting All ConnecSetting Auto Logout Time Entering Advanced Setup MenuAccepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test Return to Main Menu Setting of Search PortReturn to Default Settings Stack Projection Turn off the both projectors Setting up the Stack ProjectionProjector 1 Master Projector 2 SlaveSlave Projector MasterProjector Hub Video Wall ProjectionSetting up the Video Wall Projection Basic Click the assigning button for the desired position Access one of the four projectors via Internet ExplorerClick Video Wall on the menu Select 2 X 2 on DivisionSelect 1 X 1 on Division Click the assigning button Adjusting the Position Horizontally and VerticallyReturning to the Default Video Wall Setup Assigning the Projected Image on the Video Wall SetupVideo Wall Projection Projector Slave Setting up the Video Wall Projection ApplicationProjector 3 Slave Change the TCP/IP settings for the computer as shown belowJectors as shown below Projector Master Projector 2 SlaveMake the IP address for each pro- jector as shown below Click Stack on the menu Select Master on Stack SettingClick Stack on the menu Select Slave on Stack Setting Repeat the same procedure from the to 12 for the projector 3 When connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm Dimensions
Top Page Image Contents