Eiki/Elf EIP-4500 setup guide Stack Projection

Page 38

Stack Projection

The stack projection allows you to increase the brightness of an image by stacking two projectors and projecting same image simultaneously.

Info

•To set up the stack projection, assign a projector as the master and the other projector as the slave and connect the projectors with commercially available LAN cables (UTP cable, Category 5, cross-over type). In this way, you can control the both projectors with one remote control.

•The buttons below can control both the master and the slave at one time.

• STANDBY-ON button	• AUTO SYNC button
• BLACK SCREEN button	• RESIZE button
• INPUT 1 - 5 buttons	• PICTURE MODE button
• MUTE button	• BREAK TIMER button
• VOLUME buttons	• FREEZE button

•In normal operation, the projector set as the slave cannot be controlled by the remote control.

Only while the remote control is connected to the projector with a ø3.5 mm minijack cable (commercially available), the projector set as the slave can be controlled by the remote control.

•Even while the projector is set as the slave, the buttons on the projector can be used.

38

Image 38

Contents Setup Guide Setting up the Screen Standard Setup Front ProjectionScreen Size and Projection Distance Throw DistanceStandard Zoom Lens Standard equipment with EIP-4500 F1.8-F2.0, f=25.6-31.3 mmFixed Wide Lens AH-45201 F2.5, f=11.6 mmWide-zoom Lens AH-45301 F2.5, f=21.2-25.8 mmTele-zoom Lens AH-45501 F2.4-F2.5, f=31.9-42.5 mmTele-zoom Lens AH-45601 F2.5, f=40.8-62.8 mmTele-zoom Lens AH-45701 F2.4-F2.5, f=62.1-97.8 mmConnecting Pin Assignments RGB Input Component InputConnecting Pin Assignments Basic format RS-232C Specifications and CommandsComputer control Communication conditions Commands W RReturn Input 5 Tint -30 +30 OK or ERR CLR Temp Setting up the Projector Network Environment Connecting the projector to a computerConnecting the Pro- jector to a Computer Turn on the projector Turn on the computerSetting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Version 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Status Status Confirming the ProjectorControlling the Projector ControlProjector Settings & Adjustments Setting and AdjustingSetting the Security Network SecurityMail Originator Settings Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs GeneralMail Recipient Settings Input setup and press the Enter key Setting the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input PJS11234 and press the Enter keyWhen Connecting Using Telnet Clickstartfrom theWindows desk- top and select RunSetup Menu Main Menu 4User Name Factory default setting Not Re- quiredVView All Setting Controlling the Projector Using RS-232C or TelnetView Setting Detail List Set ItemsSSave & Quit Save Settings and QuitQuit without Saving Set Tings QQuit UnchangedSubnet Mask Setting IP Address SettingDefault Gateway Setting Projector Name Setting User Name SettingPassword Setting RS-232C Baud Rate SetEntering Advanced Setup Menu Disconnecting All ConnecSetting Auto Logout Time Data Port SettingAccepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test Return to Main Menu Setting of Search PortReturn to Default Settings Stack Projection Projector 2 Slave Setting up the Stack ProjectionProjector 1 Master Turn off the both projectorsSlave Projector MasterProjector Video Wall Projection HubSetting up the Video Wall Projection Basic Select 2 X 2 on Division Access one of the four projectors via Internet ExplorerClick Video Wall on the menu Click the assigning button for the desired positionAssigning the Projected Image on the Video Wall Setup Adjusting the Position Horizontally and VerticallyReturning to the Default Video Wall Setup Select 1 X 1 on Division Click the assigning buttonVideo Wall Projection Setting up the Video Wall Projection Application Projector SlaveProjector Master Projector 2 Slave Change the TCP/IP settings for the computer as shown belowJectors as shown below Projector 3 SlaveMake the IP address for each pro- jector as shown below Click Stack on the menu Select Master on Stack SettingClick Stack on the menu Select Slave on Stack Setting Repeat the same procedure from the to 12 for the projector 3 Troubleshooting When connecting the projector using serial-connectionTroubleshooting \ After the initialization, carry out setting again Dimensions Units inches mm