Eiki/Elf EIP-4500 setup guide After setting items, wait for 10 seconds and then re-access

Page 22

Setting up the Projector Network Environment

4 The TCP/IP setting screen ap- pears, ready for network settings for the projector.

Items	Setting example / Remarks
IP Address	Factory default setting: 192.168.150.2
	Enter an IP address appropriate
	for the network.
Subnet	Factory default setting: 255.255.255.0
Mask	Set the subnet mask to the same
	as that of the computer and
	equipment on the network.

Default	Factory default setting: 0.0.0.0
Gateway	* When not in use, set to “0.0.0.0”.

DNS	Factory default setting: 0.0.0.0
Server	* When not in use, set to “0.0.0.0”.

Note

•Confirm the existing network’s segment (IP address group) to avoid setting an IP ad- dress that duplicates the IP addresses of other network equipment or computers. If “192.168.150.2” is not used in the network having an IP address of “192.168.150.XXX”, you don’t have to change the projector IP address.

•For details about each setting, consult your network administrator.

5 Click the “Apply” button.

6

The set values appear. Confirm that the values are set properly, and then click the “Confirm” but- ton.

•After setting items, wait for 10 seconds and then re-access.

This completes the network settings.

Change the IP address of the setting computer back to its original address, and then con- nect the computer and the projector to the network.

22

Image 22

Contents Setup Guide Setting up the Screen Standard Setup Front ProjectionScreen Size and Projection Distance Throw DistanceStandard Zoom Lens Standard equipment with EIP-4500 F1.8-F2.0, f=25.6-31.3 mmFixed Wide Lens AH-45201 F2.5, f=11.6 mmWide-zoom Lens AH-45301 F2.5, f=21.2-25.8 mmTele-zoom Lens AH-45501 F2.4-F2.5, f=31.9-42.5 mmTele-zoom Lens AH-45601 F2.5, f=40.8-62.8 mmTele-zoom Lens AH-45701 F2.4-F2.5, f=62.1-97.8 mmConnecting Pin Assignments RGB Input Component InputConnecting Pin Assignments Computer control Communication conditions RS-232C Specifications and CommandsBasic format Commands W RReturn Input 5 Tint -30 +30 OK or ERR CLR Temp Setting up the Projector Network Environment Connecting the projector to a computerConnecting the Pro- jector to a Computer Turn on the projector Turn on the computerSetting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Controlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later Status Status Confirming the ProjectorControlling the Projector ControlProjector Settings & Adjustments Setting and AdjustingSetting the Security Network SecurityMail Originator Settings Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs GeneralMail Recipient Settings Input setup and press the Enter key Setting the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input PJS11234 and press the Enter keyWhen Connecting Using Telnet Clickstartfrom theWindows desk- top and select RunSetup Menu Main Menu 4User Name Factory default setting Not Re- quiredVView All Setting Controlling the Projector Using RS-232C or TelnetView Setting Detail List Set ItemsSSave & Quit Save Settings and QuitQuit without Saving Set Tings QQuit UnchangedDefault Gateway Setting IP Address SettingSubnet Mask Setting Projector Name Setting User Name SettingPassword Setting RS-232C Baud Rate SetEntering Advanced Setup Menu Disconnecting All ConnecSetting Auto Logout Time Data Port SettingCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses Return to Default Settings Setting of Search PortReturn to Main Menu Stack Projection Projector 2 Slave Setting up the Stack ProjectionProjector 1 Master Turn off the both projectorsProjector Projector MasterSlave Video Wall Projection HubSetting up the Video Wall Projection Basic Select 2 X 2 on Division Access one of the four projectors via Internet ExplorerClick Video Wall on the menu Click the assigning button for the desired positionAssigning the Projected Image on the Video Wall Setup Adjusting the Position Horizontally and VerticallyReturning to the Default Video Wall Setup Select 1 X 1 on Division Click the assigning buttonVideo Wall Projection Setting up the Video Wall Projection Application Projector SlaveProjector Master Projector 2 Slave Change the TCP/IP settings for the computer as shown belowJectors as shown below Projector 3 SlaveClick Stack on the menu Select Slave on Stack Setting Click Stack on the menu Select Master on Stack SettingMake the IP address for each pro- jector as shown below Repeat the same procedure from the to 12 for the projector 3 Troubleshooting When connecting the projector using serial-connectionTroubleshooting \ After the initialization, carry out setting again Dimensions Units inches mm