Eiki/Elf EIP-4500 Setup Menu Main Menu, 4User Name Factory default setting Not Re- quired

Page 30

Setting the Projector Using RS-232C or Telnet

SETUP MENU (Main Menu)

▼SETUP MENU

---------------------------------

SETUP MENU--------------------------------

 

[1]IP Address

[2]Subnet Mask

[3]Default Gateway

[4]User Name

[5]Password

 

[6]RS-232C Baud Rate

[7]Projector Name

 

[A]Advanced Setup

 

[D]Disconnect All

[V]View All Setting

[S]Save & Quit

[Q]Quit Unchanged

setup>

 

 

 

 

 

[1]IP Address (Factory default setting : 192.168.150.2)

IP address settings. (Page 33)

[2]Subnet Mask (Factory default setting : 255.255.255.0)

Subnet mask settings. (Page 33)

[3]Default Gateway (Factory default setting : Not Used)

Default gateway settings. (Page 33)

[4]User Name (Factory default setting : Not Re- quired)

Setting of user name for security protection. (Page 34)

[5]Password (Factory default setting : Not Required)

Setting of password for security protection. (Page 34)

[6]RS-232C Baud Rate (Factory default setting : 9600 bps)

Baud rate settings for the RS-232C terminals. (Page

34)

[7]Projector Name (Factory default setting : EIP- 4500)

It is possible to assign a projector name. (Page 34)

[A]Advanced Setup

Enters ADVANCED SETUP MENU. (Page 35)

[D]Disconnect All

Disconnect all connections. (Page 35)

[V]View All Setting

Displays all setting values. (Page 31)

Can also be used with ADVANCED SETUP MENU.

[S] Save & Quit

Save set values and quit menu. (Page 32)

[Q]Quit Unchanged

Quit menu without saving setting values. (Page 32)

ADVANCED SETUP MENU

▼ADVANCED SETUP MENU

******************** ADVANCED SETUP MENU ***********************

[1]Auto Logout Time

[2]Data Port

[5]Network Ping Test

 

[6]Accept IP Addr(1)

[7]Accept IP Addr(2) [8]Accept IP Addr(3)

[9]Accept All IP Addr

[0]Search Port

[!]Restore Default Setting [Q]Return to Main Menu

advanced>

[1]Auto Logout Time (Factory default setting : 5 min- utes)

Setting of time until automatic disconnection of net- work connection. (Page 35)

[2]Data Port (Factory default setting : 10002)

Setting the TCP port number used when exchang- ing data. (Page 35)

[5]Network Ping Test

It is possible to confirm that a network connection between the projector and a computer etc. is work- ing normally. (Page 36)

[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)

[9]Accept All IP Addr (Factory default setting : Ac- cept All)

For improved security, it is possible to set up to three IP addresses allowing connection to the projector. Set IP addresses can be cancelled using [9] Accept All IP Addr. (Page 36)

[0] Search Port (Factory default setting : 9300)

Setting the port number used when searching for the projector. (Page 37)

[!]Restore Default Setting

Restores all setting values that can be set using the

menu to the default state. (Page 37)

[Q]Return to Main Menu

Return to the main SETUP MENU. (Page 37)

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Setup Guide Setting up the Screen Standard Setup Front ProjectionScreen Size and Projection Distance Throw DistanceStandard Zoom Lens Standard equipment with EIP-4500 F1.8-F2.0, f=25.6-31.3 mmFixed Wide Lens AH-45201 F2.5, f=11.6 mmWide-zoom Lens AH-45301 F2.5, f=21.2-25.8 mmTele-zoom Lens AH-45501 F2.4-F2.5, f=31.9-42.5 mmTele-zoom Lens AH-45601 F2.5, f=40.8-62.8 mmTele-zoom Lens AH-45701 F2.4-F2.5, f=62.1-97.8 mmConnecting Pin Assignments RGB Input Component InputConnecting Pin Assignments RS-232C Specifications and Commands Computer control Communication conditionsBasic format Commands W RReturn Input 5 Tint -30 +30 OK or ERR CLR Temp Setting up the Projector Network Environment Connecting the projector to a computerConnecting the Pro- jector to a Computer Turn on the projector Turn on the computerSetting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Controlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Status Status Confirming the ProjectorControlling the Projector ControlProjector Settings & Adjustments Setting and AdjustingSetting the Security Network SecurityMail Originator Settings Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs GeneralMail Recipient Settings Input setup and press the Enter key Setting the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input PJS11234 and press the Enter keyWhen Connecting Using Telnet Clickstartfrom theWindows desk- top and select RunSetup Menu Main Menu 4User Name Factory default setting Not Re- quiredVView All Setting Controlling the Projector Using RS-232C or TelnetView Setting Detail List Set ItemsSSave & Quit Save Settings and QuitQuit without Saving Set Tings QQuit UnchangedIP Address Setting Default Gateway SettingSubnet Mask Setting Projector Name Setting User Name SettingPassword Setting RS-232C Baud Rate SetEntering Advanced Setup Menu Disconnecting All ConnecSetting Auto Logout Time Data Port SettingSetting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses Setting of Search Port Return to Default SettingsReturn to Main Menu Stack Projection Projector 2 Slave Setting up the Stack ProjectionProjector 1 Master Turn off the both projectorsProjector Master ProjectorSlave Video Wall Projection HubSetting up the Video Wall Projection Basic Select 2 X 2 on Division Access one of the four projectors via Internet ExplorerClick Video Wall on the menu Click the assigning button for the desired positionAssigning the Projected Image on the Video Wall Setup Adjusting the Position Horizontally and VerticallyReturning to the Default Video Wall Setup Select 1 X 1 on Division Click the assigning buttonVideo Wall Projection Setting up the Video Wall Projection Application Projector SlaveProjector Master Projector 2 Slave Change the TCP/IP settings for the computer as shown belowJectors as shown below Projector 3 SlaveClick Stack on the menu Select Master on Stack Setting Click Stack on the menu Select Slave on Stack SettingMake the IP address for each pro- jector as shown below Repeat the same procedure from the to 12 for the projector 3 Troubleshooting When connecting the projector using serial-connectionTroubleshooting \ After the initialization, carry out setting again Dimensions Units inches mm
Top Page Image Contents