Eiki/Elf EIP-4500 setup guide Repeat the same procedure from the to 12 for the projector 3

Page 49

(See page 86 on the owner’s manual of the projector.)

Note

• Set input terminals you will use to “ON”. Set input terminals you will not use to “OFF”.

15 Turn off all of the projectors.

16 Make connections following the diagram shown on page 46.

17 Turn on the projectors first, then turn on the computers and the video equipment.

Note

• Image quality may deteriorate when picture sig- nals are input through multiple projectors with an RGB cable or an RCA cable in a daisy chain connection.

Select inputs as specified in the table on the right.

13 Repeat the same procedure from the step 10 to 12 for the projector 3 and 4.

Video Wall Projection

14

Projector 1

Master

Set Inputs

INPUT1	ON
INPUT2	ON
INPUT3	OFF
INPUT4	ON
INPUT5	OFF

Projector 2-4

Slave

Set Inputs

INPUT1	ON
INPUT2	OFF
INPUT3	OFF
INPUT4	ON
INPUT5	OFF

49

Image 49

Contents Setup Guide Standard Setup Front Projection Setting up the ScreenThrow Distance Screen Size and Projection DistanceF1.8-F2.0, f=25.6-31.3 mm Standard Zoom Lens Standard equipment with EIP-4500F2.5, f=11.6 mm Fixed Wide Lens AH-45201F2.5, f=21.2-25.8 mm Wide-zoom Lens AH-45301F2.4-F2.5, f=31.9-42.5 mm Tele-zoom Lens AH-45501F2.5, f=40.8-62.8 mm Tele-zoom Lens AH-45601F2.4-F2.5, f=62.1-97.8 mm Tele-zoom Lens AH-45701RGB Input Component Input Connecting Pin AssignmentsConnecting Pin Assignments Computer control Communication conditions RS-232C Specifications and CommandsBasic format W R CommandsReturn Input 5 Tint -30 +30 OK or ERR CLR Temp Connecting the projector to a computer Setting up the Projector Network EnvironmentTurn on the projector Turn on the computer Connecting the Pro- jector to a ComputerSetting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Controlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later Controlling the Projector Confirming the ProjectorStatus Status ControlSetting the Security Setting and AdjustingProjector Settings & Adjustments Network SecuritySetting for Sending E-mail when an Error Occurs Making General Settings for the Network NetworkMail Originator Settings GeneralMail Recipient Settings When Connecting Using RS-232C Setting the Projector Using RS-232C or TelnetInput setup and press the Enter key Input PJS11234 and press the Enter keyClickstartfrom theWindows desk- top and select Run When Connecting Using Telnet4User Name Factory default setting Not Re- quired Setup Menu Main MenuView Setting Detail List Controlling the Projector Using RS-232C or TelnetVView All Setting Set ItemsQuit without Saving Set Save Settings and QuitSSave & Quit Tings QQuit UnchangedDefault Gateway Setting IP Address SettingSubnet Mask Setting Password Setting User Name SettingProjector Name Setting RS-232C Baud Rate SetSetting Auto Logout Time Disconnecting All ConnecEntering Advanced Setup Menu Data Port SettingCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses Return to Default Settings Setting of Search PortReturn to Main Menu Stack Projection Projector 1 Master Setting up the Stack ProjectionProjector 2 Slave Turn off the both projectorsProjector Projector MasterSlave Hub Video Wall ProjectionSetting up the Video Wall Projection Basic Click Video Wall on the menu Access one of the four projectors via Internet ExplorerSelect 2 X 2 on Division Click the assigning button for the desired positionReturning to the Default Video Wall Setup Adjusting the Position Horizontally and VerticallyAssigning the Projected Image on the Video Wall Setup Select 1 X 1 on Division Click the assigning buttonVideo Wall Projection Projector Slave Setting up the Video Wall Projection ApplicationJectors as shown below Change the TCP/IP settings for the computer as shown belowProjector Master Projector 2 Slave Projector 3 SlaveClick Stack on the menu Select Slave on Stack Setting Click Stack on the menu Select Master on Stack SettingMake the IP address for each pro- jector as shown below Repeat the same procedure from the to 12 for the projector 3 When connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm Dimensions