Eiki/Elf EIP-4500 Setting up the Stack Projection, Projector 1 Master, Projector 2 Slave

Page 39

Stack Projection

Setting up the Stack Projection

Basic

This part shows an example for setting up the stack projection of a computer image with two projectors.

Projector 1: Master

INPUT 1 terminal

Projector 2: Slave

INPUT 1 terminal

RGB cable

OUTPUT (FOR INPUT 1, 2) terminal

LAN terminal

RGB

cable LAN cable (cross-over type)

Computer

LAN terminal

1 Set the “Stack Setting” of the pro-	4
jector 1 to “Master”.

(See page 84 on the owner’s manual of the projector.)

Select inputs as specified in the table below.

(See page 86 on the owner’s manual of the projector.)

2 Set the “Stack Setting” of the pro- jector 2 to “Slave”.

(See page 84 on the owner’s manual of the projector.)

3 Perform “Pair Stack” of the both projectors.

(See page 85 on the owner’s manual of the projector.)

Projector 1

Master

Set Inputs

INPUT1	ON
INPUT2	OFF
INPUT3	OFF
INPUT4	OFF
INPUT5	OFF

Projector 2

Slave

Set Inputs

INPUT1	ON
INPUT2	OFF
INPUT3	OFF
INPUT4	OFF
INPUT5	OFF

5 Turn off the both projectors.

39

Image 39

Contents Setup Guide Standard Setup Front Projection Setting up the ScreenThrow Distance Screen Size and Projection DistanceF1.8-F2.0, f=25.6-31.3 mm Standard Zoom Lens Standard equipment with EIP-4500F2.5, f=11.6 mm Fixed Wide Lens AH-45201F2.5, f=21.2-25.8 mm Wide-zoom Lens AH-45301F2.4-F2.5, f=31.9-42.5 mm Tele-zoom Lens AH-45501F2.5, f=40.8-62.8 mm Tele-zoom Lens AH-45601F2.4-F2.5, f=62.1-97.8 mm Tele-zoom Lens AH-45701RGB Input Component Input Connecting Pin AssignmentsConnecting Pin Assignments RS-232C Specifications and Commands Computer control Communication conditionsBasic format W R CommandsReturn Input 5 Tint -30 +30 OK or ERR CLR Temp Connecting the projector to a computer Setting up the Projector Network EnvironmentTurn on the projector Turn on the computer Connecting the Pro- jector to a ComputerSetting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Controlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Control Confirming the ProjectorControlling the Projector Status StatusNetwork Security Setting and AdjustingSetting the Security Projector Settings & AdjustmentsGeneral Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs Mail Originator SettingsMail Recipient Settings Input PJS11234 and press the Enter key Setting the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input setup and press the Enter keyClickstartfrom theWindows desk- top and select Run When Connecting Using Telnet4User Name Factory default setting Not Re- quired Setup Menu Main MenuSet Items Controlling the Projector Using RS-232C or TelnetView Setting Detail List VView All SettingTings QQuit Unchanged Save Settings and QuitQuit without Saving Set SSave & QuitIP Address Setting Default Gateway SettingSubnet Mask Setting RS-232C Baud Rate Set User Name SettingPassword Setting Projector Name SettingData Port Setting Disconnecting All ConnecSetting Auto Logout Time Entering Advanced Setup MenuSetting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses Setting of Search Port Return to Default SettingsReturn to Main Menu Stack Projection Turn off the both projectors Setting up the Stack ProjectionProjector 1 Master Projector 2 SlaveProjector Master ProjectorSlave Hub Video Wall ProjectionSetting up the Video Wall Projection Basic Click the assigning button for the desired position Access one of the four projectors via Internet ExplorerClick Video Wall on the menu Select 2 X 2 on DivisionSelect 1 X 1 on Division Click the assigning button Adjusting the Position Horizontally and VerticallyReturning to the Default Video Wall Setup Assigning the Projected Image on the Video Wall SetupVideo Wall Projection Projector Slave Setting up the Video Wall Projection ApplicationProjector 3 Slave Change the TCP/IP settings for the computer as shown belowJectors as shown below Projector Master Projector 2 SlaveClick Stack on the menu Select Master on Stack Setting Click Stack on the menu Select Slave on Stack SettingMake the IP address for each pro- jector as shown below Repeat the same procedure from the to 12 for the projector 3 When connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm Dimensions