Eiki/Elf EIP-4500 Setting the Projector Using RS-232C or Telnet, When Connecting Using RS-232C

Page 28

Setting the Projector Using RS-232C or Telnet

Connect the projector to a computer using RS-232C or Telnet, and open the SETUP MENU on the computer to carry out various settings for the projector.

When Connecting Using RS-232C

1 Launch general purpose terminal emulator.

2 Input settings for the RS-232C port of the terminal emulator as follows.

Baud Rate	: 9600 bps*
Data Length	: 8 bit
Parity Bit	: None
Stop Bit	: 1 bit
Flow Control	: None

*This is the factory default setting. If the value of Baud Rate for the projector has been changed, set Baud Rate here according to the changed value on the projector.

3 Input “PJS11234” and press the “Enter” key.

7 “Password:” is displayed. Input the password and press the “Enter” key.

•If a password has not yet been set, just press the “Enter” key.

8 Input “setup” and press the “Enter” key.

•SETUP MENU will be displayed.

▼SETUP MENU

---------------------------------	SETUP MENU--------------------------------
	SETUP MENU--------------------------------
[1]IP Address	[2]Subnet Mask	[3]Default Gateway
[4]User Name	[5]Password
[6]RS-232C Baud Rate	[7]Projector Name
[A]Advanced Setup		[D]Disconnect All
[V]View All Setting	[S]Save & Quit	[Q]Quit Unchanged
setup>

Note

•User name and password are not set in the fac- tory default settings.

•If the user name or password is entered incor- rectly three times, SETUP MENU will be quit.

4 “OK” is displayed. Input “PJS25678” and press the “Enter” key within 10 seconds.

5 “OK” is displayed. Press the “En- ter” key.

6

“User Name:” is displayed. Input the user name and press the “Enter” key.

•If a user name has not yet been set, just press the “Enter” key.

28

Image 28

Contents Setup Guide Setting up the Screen Standard Setup Front ProjectionScreen Size and Projection Distance Throw DistanceStandard Zoom Lens Standard equipment with EIP-4500 F1.8-F2.0, f=25.6-31.3 mmFixed Wide Lens AH-45201 F2.5, f=11.6 mmWide-zoom Lens AH-45301 F2.5, f=21.2-25.8 mmTele-zoom Lens AH-45501 F2.4-F2.5, f=31.9-42.5 mmTele-zoom Lens AH-45601 F2.5, f=40.8-62.8 mmTele-zoom Lens AH-45701 F2.4-F2.5, f=62.1-97.8 mmConnecting Pin Assignments RGB Input Component InputConnecting Pin Assignments Computer control Communication conditions RS-232C Specifications and CommandsBasic format Commands W RReturn Input 5 Tint -30 +30 OK or ERR CLR Temp Setting up the Projector Network Environment Connecting the projector to a computerConnecting the Pro- jector to a Computer Turn on the projector Turn on the computerSetting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Controlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later Confirming the Projector Controlling the ProjectorStatus Status ControlSetting and Adjusting Setting the SecurityProjector Settings & Adjustments Network SecurityMaking General Settings for the Network Network Setting for Sending E-mail when an Error OccursMail Originator Settings GeneralMail Recipient Settings Setting the Projector Using RS-232C or Telnet When Connecting Using RS-232CInput setup and press the Enter key Input PJS11234 and press the Enter keyWhen Connecting Using Telnet Clickstartfrom theWindows desk- top and select RunSetup Menu Main Menu 4User Name Factory default setting Not Re- quiredControlling the Projector Using RS-232C or Telnet View Setting Detail ListVView All Setting Set ItemsSave Settings and Quit Quit without Saving SetSSave & Quit Tings QQuit UnchangedDefault Gateway Setting IP Address SettingSubnet Mask Setting User Name Setting Password SettingProjector Name Setting RS-232C Baud Rate SetDisconnecting All Connec Setting Auto Logout TimeEntering Advanced Setup Menu Data Port SettingCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses Return to Default Settings Setting of Search PortReturn to Main Menu Stack Projection Setting up the Stack Projection Projector 1 MasterProjector 2 Slave Turn off the both projectorsProjector Projector MasterSlave Video Wall Projection HubSetting up the Video Wall Projection Basic Access one of the four projectors via Internet Explorer Click Video Wall on the menuSelect 2 X 2 on Division Click the assigning button for the desired positionAdjusting the Position Horizontally and Vertically Returning to the Default Video Wall SetupAssigning the Projected Image on the Video Wall Setup Select 1 X 1 on Division Click the assigning buttonVideo Wall Projection Setting up the Video Wall Projection Application Projector SlaveChange the TCP/IP settings for the computer as shown below Jectors as shown belowProjector Master Projector 2 Slave Projector 3 SlaveClick Stack on the menu Select Slave on Stack Setting Click Stack on the menu Select Master on Stack SettingMake the IP address for each pro- jector as shown below Repeat the same procedure from the to 12 for the projector 3 Troubleshooting When connecting the projector using serial-connectionTroubleshooting \ After the initialization, carry out setting again Dimensions Units inches mm